How to wire a 2 prong 12v rocker switch

LIKE, COMMENT, SUBSCRIBE.
Connect your power source positive to one end of the terminal.
Take another positive wire form the other end of the switch terminal connect it to your load. Make sure to ground your load.
Load is powered ONLY when the switch is toggled to the ON position.

If you enjoyed this video help others enjoy it by sharing this video with your friends:
And if you have any questions or comments, leave it in the comment section below.

If you would like to help support the channel? Here is an easy way to do so. I really appreciate your donation and support to cover some of the costs I have, making this content. Thank you!
$5.00

This is the links below to things I used in this video:

Affiliate disclaimer:
The links above are affiliate links, which will/may generate a sales commission. For example, the listed above its association with the Amazon affiliate program and I’m an Amazon associate. Which means that if you buy one of the product links, I’ll receive a small commission at no extra cost to you?
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future videos, and like my video, click on the bell to see more if you found it helpful, new videos are always being uploaded.

Follow me on

Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only.
PLEASE READ Warning… do this at your own risk. I am not responsible for what you do to your device.

#howtowirea2prong12vrockerswitch #alwynnicholas #howto

[Fisheee]

I made a under cabinet lighting led strip for my mom's kitchen, and I used this video to figure out how to wire the switch. Thank you!

[cesarlarancuent]

Finally someone explained the right way,
Before this video I watched about 10 others videos and no one show it the right way,
Thank you for making this video 👍🏽, .

[AlmightyRandy]

Out of all the videos I’ve seen this was the best one. Straight to the point and answered all my questions all at once.👍👍👍👍👍

[Classy_Car]

Thank you, i was confused on where the grounds would go lol. This helped me.

[dannyblair]

Thank you for taking the time to make this video, very simply explained at a nice pace, love the voice.

[Trey]

You’re the man. You just made my life so simple 😂

[itsme.dajaaa]

Is there a link to the battery you used?

[jwrhynejr.]

Thank you, sir!! Tremendous help for my DIY rigging 12 volt pump to use for off grid shower rig!! my water heater died & I made a shower rig with parts & pump for stove heated water!❤

[cherijeffcoat]

Well done. To the point and easy directions to follow. Thank you very much.

[ChristiannTyler]

I'm working on a project and could use some ideas. I'm designing a cabinet to house my radio equipment, which tends to generate a lot of heat. I'm planning to incorporate 3-4 12V fans into the design, each with its own switch. The goal is to provide ventilation without having all the fans turn on simultaneously every time the power supply is switched on. Any suggestions for how to set this up effectively?

[stephenceravolo]

Simple and easy explanation! Thank you so much!!!

[HIGHROLLAZAUTOCLUB]

But you have an inline fuse on your positive and didn’t say what size fuse and why your using it and how to know the size to use.

[garyenwards]

Do you need the inline fuse on the wire from the switch to the battery if you are also using a relay for a cars radiator fan? There is a fuse from the battery to the relay but the switch will have a wire to the relay and a wire to the battery. Thank you

[petermcmahon]

Clear, concise & helpful. Thank you

[caffeinatedguy]

Can I just loop the wire around the holes of the contact pin then cover it with electrical tape?

[jaybee]

I understand the whole open and closed circuit. But why can’t you just hook the negative wires together and the positive together and put females on them and connect the negative and positive to each prong..?? I know the flow has to be consistent and a break in one wire to open and close the flow of power. I just was never told why u can’t do it the way I mentioned.. thxs for any logical knowledge you give appreciate it..

[binayakbishnu]

What is the name of the connector used to connect to the pons of the switch

[IVIylostpotato]

Great video thanks actually helped me understand the 5 pin better I appreciate it

[panmad]

I need to replace the rocker switch on my ebike lithium battery. I'm not sure which type to buy. Can you help? There's a sub in it if you can..lol

[dansmodeluniverse]

Perfect, simple explanation. Thank you.