Push Start PKE | Aftermarket Installation Safety Precautions & Risk

*** Dear folks if you think this video is helpful to you, please subscribe I need your support ***
The safety precautions that users need to know before converting cars to Push Start System. This is very important so you can decide whether to upgrade your car to a modern tech but risky or stay safe on conventional key start systems.
Here in this video I will show the problem that you guys might encountered with push aftermarket start system and how to resolved it.

Link to Product:
Keyless Model: Q6B

Interested to review your products with me

[mianfazlerazik]

Or just open it up and put alot of transparent nailpolish on it as a protective layer. Works like a charm

[daltonhaughton]

I would love if you would do a video on the complete installation of the unit in a car for the DIY persons please 👍

[vallorahn]

I disagree, going from cold to hot creates condensation because air pressure difference in different temperatures. Since different air pressures have different humidity level, the leftover water condensates. if you wrap it in plastic, it basically condensates inside and cannot vaporize again because well, you wrapped in plastic, but it got inside with air, since you cannot make it completely air tight by wrapping it in plastic. So you just create a closed canister that keeps sucking water in from air. What I would to is get a can of spray polyurethane plastic and coat the PCB. Now its just protected from the environment. Ofcourse it is good to clean the board first with isoprophyl alcohol. Simple. And now the condensation water can leave before causing any harm by rusting your connectors, etc.

[okicom]

i had a more expansive system been using it for quite number of year, at the end of the days when the relays start to get weak, you will find your car will have a hard to start and sometimes doesn't even start. currently i haven't found any better system which is more reliable from china.

[Drrrre]

Very impressive diagnosis. Thank you for sharing your findings.

[blemdog]

Do you think a silicone based or epoxy resin, if I coat the entire circuit board with one of them, it will prevent moisture from getting in there

[Gbody_Plus]

Got it installed and used to not turn on with out the key fob in range but idk what happened it starts with out the fob I’m range what could it be

[mukundpatil]

Both remotes lost what to do in this case

[ModItBetter]

good video and good eye for finding the bridge.. the chip though that looks more like they acid wiped or used a grinder on it to get rid of the writing on the chip so you would not know what it is .. I see that in all the products from china . They do it to slow people down from cloning the pcb's or dumping the firmware off the chip and the other reason is because the chip it self is a clone of a name brand..
I Just bought one of those to install have not taken mine apart yet but pretty sure that is the wireless section and that would not cause your car to turn on and off anyways.

[jobbeltran]

I am very impressed with the knowledge shared. I subscribed. I am planning to install one and I'm going to spray it with PCB protective spray.

[fredautronicsdiy]

Thank you my friend...such a good product review..

[eranopaden]

Hi, I have the same brand but the Q6A model. Before the two remote key fob is working fine. But now only one is working. The thing is when I press the button of the key fob the led light still works but the lock of the door doesn’t open. Is there a way to reprogram the remote? Thanks

[themaher]

Hi Ikmal, would you please make a video about the full installation of this kit. Thanks

[adamtineo]

This was an awesome video until you said to use the bag. This unit produces heat, if you bag This the heat will sit inside bag and literally make condensation due to the heat produced inside of the plastic. Recall microwaving a meal, the top plastic has water/condensation due to the heat being produced underneath. Maybe don't advise that.

[ashrafrahim]

What if the car have immobiliser system?still suggested to install?

[robertbutler]

Warning I have the EASYGUARD PKE system All remotes shit themselves at some point I advise when ordering to get two more remotes straight away because, after a couple of years, the new remotes will not work on the older module. I know because it happened to me.

[devavighnen]

Hi, amazing diagnosis of the PKE system. I have one problem with my aftermarket PKE, it's that holding the brake and pushing the Push to Start button starts up the car way too fast, and this over time is causing some problems with the idling due to ECU. My question; is there any way for us to add a delay in the PCB when we start the car? only pressing the button without pressing brake sets car to "ON" position and starts the ECU, but when we try to start the engine, the starting sequence is Off -> Immediately Start Engine which does not help. Thank you so much for your input

[luckyanmsn]

my car has 4 wire ignetion switch and this system has 6 wire . can you tell me how can i install this ? 2 wire extra . 1 is negative and one extra ignation . where i connect that extra ignation wire ? please help me .

[akeemmayowa]

Hello, I have installed my own but he can not start the engine, and the I try several time is the same, can anybody help me maybe there is a wire that I did not put

[MrINTELIKXX]

Mungkin boleh ..solder dengan cairan plastik atau..buat dia waterproof.. Boleh tak spray atau solder supaya tertutup .. Guna leakage spray..
Eksperimen ..hihi asalkan bahan penutup bukan elektrostatik..konduktor elektrik..