HY-DIV268N-5A Stepper Motor NEMA 23 with Arduino mega / UNO - zonemaker.com

#zonemaker

This video is about HY-DIV268N-5A CNC Single Axis TB6600 0.2A to 5A Two Phase Hybrid Stepper Motor Driver Controller

HY-DIV268N-5A is is a PWM chopper-type single-chip bipolar sinusoidal micro-step stepping motor driver. 2-phase bipolar-type stepping motor can be driven by only clock signal with low vibration and high efficiency. Suitable for drive Two-phase stepping motor dynamic voltage 12V to 48V, the maximum drive current is less than 5A and having outer diameter of 35 to 86 mm.

This drive uses the current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth. High-speed torque is much higher than other two-phase drives, high positioning accuracy. Widely used in the engraving machines, CNC machine tools, packaging machinery and other high resolution requirements on the device. NEMA17, NEMA23, NEMA24 and NEMA34 stepper motors work perfectly with this HY-DIV268N-5A Stepper Driver.

[chrisnothnagel]

This is exactly how these video lessons should be made. Clear and to the point. Good work.

[Flyrip]

The best video I have seen about driving a stepper motor. Simple, clear and to the point 👍🏻👍🏻. Lots of thanks!! 😊

[chrisBruner]

Exactly what I was looking for. Thanks!

[WeolocoMr]

un video hermoso! al punto y sin tanta vaina! Thanks for the information

[colsanjaybajpai]

Excellent and very well annotated video

[anuragshrivastava]

Thank you so much for explaining step by step

[مريممريمي-خج]

عمل مرتب كان وواضح للمشاهد ..عاشت جهودك

[patprop]

This video is a few years old, You now had plenty of time to test out the drivers, how do you like them? are they worth buying or not? 3:19 Who''s the cutie that popped up?

[jimmihenry]

I am confused by the lable 5A. The datasheet of the TB6600HG sais 4, 5A and 5A 100ms peak.

[danycourvoisier]

I do the same way as you do
But it doesn't work for me I still don't know why.


I already connected all the cables as you make but not work for me

[useruseruser]

Do you mind connecting the drives separately instead of connecting them to a single power source?

[yasmintv]

Plz help to microstep switch set.. in my tb6600 nothing is 1/8, only exist NC, 1, 2/A, 2/B, 4, 8, 16, 32.
Which one should i choose.?

[fabianadasilvareservado]

what is the connection of the wires so that the motors turn in the same direction when they are facing each other

[MJApple]

Thanks, how we can connect it to Blynk app by Wifi, a video will be much appreciated <3

[davidwaidelich]

when running two steppers parallel do you double the current to accommodate two motors, and what wires do you connect to for 3 steppers on a mega without ramp shield?

[yigageorgewilliams]

Would like to use Ramps 1.4 and mega with nema 23, what's your thought about that?

[PardeepKumar-gwow]

Sir please explain program code to control stepper motor

[pramodjalgaonkar]

Madam stepper motor noise bahut karta hai
Koi eesi motor batao noise bhi kam aaye or torque bhi aavha mile

[AmeenHandyMan]

wanna ask if i put 2 stepper motor nema 17 which 1 stepper motor 1.5A how do i set current? should i set 3A or just set 1.5A?

[parasaniasandip]

How to decide the driver input power supply voltage and amp ? 🌿