How To Quickly Fix Broken Pads w/ The Refox Soldering Lug. Premade Jumpers & Pads for Microsoldering

Have you ever lifted an IC and noticed there was a ripped pad underneath, or you split a sandwich board & see there are missing pads you need to rebuild?

Well, good news! The Refox Soldering Lugs are essentially pre-made jumpers & pads that make these types of repairs so much easier to deal with.

We also walk through an example of how to use this on an iPhone 8 Plus with broken WiFi pads.

B2B Pricing available for repair shops. Contact us for more info.

🔧Here's some of the tools we used🔧

🔥🔥Support the channel & check out the links below🔥🔥

Please note: This page contains affiliate links. If you choose to make a purchase after clicking a link, I may receive a commission at no additional cost to you. Thank you for your support!

[NigelB-czbz]

I love using these and its great seeing someone of your caliber using them. Much easier than using jumper wire. Great idea to keep the cut off bits as jumpers too. Keep the videos coming

[saltcityrepairs]

As always, You are amazing Idol Jesse 👍💪👈❤️

[southbaymobilerepairs]

Great demo! I ordered some because of this video. Thanks!

[Nectronixx]

Love these! Thanks for the video Jesse!

[profixerr]

i smashed the like button so hard on this one! great video like always!!

[SURGE]

Great video and they really do look good them pad repair kits👍

[opZylo]

Thank you for this video, very helpful!

[FlyZoneFpv]

Right on thanks for this tip and tutorial 👊🏻

[MaSter-svir]

Great videos. I wanted to ask I was trying to solder fpc connectors for touch on iPad 8 however I couldn’t get the new connectors to be soldered well and the popped out. Then I messed up two of the pads on the board. My question is why the fpc connectors didn’t soldered well and if I should now buy those pads to solder on the board?
I cleaned the area with isolated alcohol and applied flux and then tried to solder the new fpc but it didn’t go well. I tried to apply some soldering paste but I couldn’t get it to apply well on each pad as the paste was moving around all over the pads and not individually. I’ll highly appreciate your explanation on how to do it the clean way.

[kamierankalil]

How do I replace the timing crystal points?

[advancedleveldiagnostics]

Great job! would it work to put a little glue under the pad to give it more support?

[MicroMageRepair]

Nice video Jesse. My opinion on them is they are pretty good when you can use them straight on, if you got to route the tail anywhere jumpers appear to be better. Just my experience so far. I did use the round pads to fix a few ripped off filter pads on an iPad recently. That was interesting.

[catharperfect]

I ripped a couple because my solder wick got stuck to them. Maybe I should've used more flux. And/or not pushed down as much on the iron. Thanks for the heads up though.

[bryzztortello]

I have em. still pretty hit or miss for me with them. ill get it down eventually like you

[fritzj]

Do you have a link for UV masking liquid?

[zlatovskyful]

nice video, I appreciate. I’d have one question, is there any other solution besides uv to stabilise the pad on the pcb? Some type of glue etc? Thanky you

[marcusjames]

Thank you for a great video I mend a lot of Xbox;s one x, and I am just starting to reflow chips Can you tell me what temperature to replace hdmi timer chip and some of the chips on the power rail near the hdmi chip the power rail chip is the only one chip that I can’t buy for some reason we’re is the best place to buy replacement caps and other parts and components and do you no were I can get a full schematic of the main board I’ve looked everywhere and can’t seem to find the right one MENY thanks mark

[dnantis]

Awesome video !!
Just want to ask you ...why there is no special epoxy to extra secure that pad glued to the old pcb area ??
Or like using CA glue to fixate the copper to the actual missing pad area ??
Have you tried this ??
I know is a pain to do if there are 10 pads to fix but how come we have to endure using UV mask to fixate that little new pad ??
Is it that the new copper pad wont accept any glue added to it ??

[jessihawkins]

I looked at the uv light on your video and damaged my eyesight 😩

[bshi]

hello.What tool do you use for picking up and cutting tiny jumper wire in this tutorial?