How to Bind | RadioMaster R Series V2 Receiver Bind Instructions

In this tutorial video, we will show you how to bind the R series V2 receivers to your RadioMaster Radio. So watch this video and all will be explained.

🎥Follow us on:
- Youtube: @RadioMasterRC
#RadioMaster #receivers

[bunnykiller]

I was given a Radiomaster TX16S and a Mobula6 quad and no one could get it to bind ( the previous owner, me, and 2 other flyers) so I bought a R86C rcvr and an ESC and motor to test things out... your instructions worked you teach, the other videos just remind how to do it... thank you for putting this very helpful video up.... now I need to make a plane for this new rcvr and motor assy ;)

[gliderrider]

I’m new so this is very helpful. Thanks!

[hinterkress]

To anyone who thinks this demonstration is next to useless, the fact that it's about as helpful as any other instructions put out by RadioMasterrc shouldn't be surprised!!
After f#cking about for an hour or so I got my RADIOMASTER R84-V2 RX to bind to my RADIOMASTER Tx-16S TX using Frsky-D mode and D8 RF protocol. Why can't they just put that in the manual?

[lokaero]

Hi. Here is an awesome update about R88 receiver. finally after testing the blank (4th pin) the pin which is mentioned as 'X' in usermanual which is present near the SBUS port i found out that its the external voltage measurement pin which measures and transmits voltage value to the transmitter with "A2" label. I tested it with my R88 V2 receiver in D16 mode. not sure if it works with R88 V1 or D8 mode. Initially the ratio needed to be calibrated for accurate voltage value.

[lokaero]

Hi. im using QX7 ACCESS radio. i have issue binding with Radiomaster R88 V2 receiver which supports ACCST D16. im unable to bind to this receiver. i tried updating the ISRM on the radio but still unable to bind with R88 V2 receiver. is there any solution or fix? i tried to downgrade the ISRM to qx7 access ISRM version 1.1.3. and it got bound. but i can notice some packet loss while moving the servos. do you guys have separate firmware for R88 receivers to support ACCST D16 (V2)?

[stylealone]

I use model Radiomaster Boxer (Elrs) . Which receiver model should I use?

Thank you very much. From Thailand

[alfredo]

Als ik het wist hoef ik het niet op te zoeken, misschien in een wat langzamer tempo, zodat je het ook kunt volgen 😪

[ajishtm]

Is the v2 reciever is suitable for radiomaster pocket elrs version

[colinbarnes]

Please make a video on setting up the Ranger Nano ELRS module with the Zorro radio

[coolaboris]

What is that thing connected to the battery, that is "switched on"?

[henrik]

I just received three receivers of the v2 series. 2x R84 and 1x R86. Unfortunately none of them enters into bind mode. I tried differend power sources, always pressing bind when connecting to power source. Any hints what could be the issue?

[dandork]

I thought the receiver was massive until I saw your hands next to the radio.

[bhaiyajitechnical]

noit able to connect with zoro elrs verson
please help

[radilux]

I get low range issue with Zorro and r86 - r86c and r88 . All of them are v2 versions.
Smae protocol like shown. Fine tuning diest help...
Any ideas ?

[CliffHarveyRCPlanes]

Reading through the few comments I notice the speed of the video is criticised, the answer is to slow it down, easily done with the options on the settings 'wheel' 🤔👍

[RandoManFPV]

Please make a video clearly explaining how to put the radiomaster tx16s into mode 3(physical changes to gimbals)


I just want my left gimbal to fall all the way down when released.
At this moment I can set it to return to center(like a video game controller) when I release the gimbal.
Or I can set it to stay where I leave it(on vertices axis) when I release the gimbal. Like I can set it at half throttle, let go of gimbal and it'll stay at half throttle. But this isn't what I want.

I just want the gimbal to fall from gravity acting on it when I release the gimbal. That way when I let go of the throttle(release the gimbal) it will automatically return to 0 throttle.

[akmalmarzuki]

Why i just got 100- 200m range instead of advert almost 1km

[alexii]

can you do this a little faster; I was almost able to follow but not quite; if you go faster, we will not see anything; also thanks for not telling us what is that other device you attached to the battery and then to the receiver;
oh and try not to talk so that we have no idea what you are doing

[f-tigwelder]

I have a brand new TX16S radio and I'm ready to throw it in the trash can. ZERO instructions!!!! All I want to do is fly this airplane, but have spent 2 days f@#king with it and still won't work. Try to call the guy who talked me out of the Spectrum radio because there no good. Now he can't be reached by phone, just email says the recording (2 days ago) How do I know what protocol I need???? It's a R84 receiver, oh yea NO instructions!! AGAIN. You have to be a F*#KING Computer engineer to figure this thing out. Come on. Do company's just assume you go to YouTube for all information all their product. Just tell me each setting I need, this guy is going so fast you don't know what he's changing settings to.

[RCREVIEWS]

REALLY?? WHY EVEN BOTHER MAKING THIS VIDEO?