Testing $300 Amazon Supercharger: Will It Blow??

[DISCOSHOEBOX]

The Aisin AMR supercharger rotors aren't plastic, they are Teflon coated. The same applies to the Toyota SC12 & SC14, they are Teflon coated. Spinning them too fast, generates a lot of heat - which causes the Teflon to delaminate.
The supercharger you've installed is a Toyota sc14 which displaces the same as an Eaton M90. Try to keep the SC14 under 15, 000 rpm and it won't delaminate. The biggest upgrade to a supercharged engine is to install a set of headers. For a supercharged engine the primary pipe size should to two sizes about what is normally used for N\A - 1.75 inch primary pipes into a single collector should do the trick.
The supercharger should be governed - Toyota used these on the 1G-GZE and the throttle body was in front of the supercharger, the ducting then ran through an intercooler before entering the engine. Of course its your car, so do as you please. This is just a bit of information for you to gain some insight as to what you have bought.

[Adam-nvzo]

I think this car would be a perfect candidate for a rebuilt junkyard M90 supercharger.

[danielolah]

I'm definetly not an expert with superchargers but maybe putting an intercooler would be a good idea, main reason not to cool the air but to filter out the plastic pieces in case something bad happens. Love theese budget builds tho

[Tarmo]

Put an intercooler on that so it catches the fragments if the rotors explodes and also dump valve in pressure side is recommented so it dont cause too much pressure when coming off the throttle, done that on volvo engine before.

[spadeykins]

30 seconds in and I can already tell this channel is going to BLOW up! Subscribed

[dsmmonster]

A few years ago I installed a supercharger from a Mercedes compressor in a Miata 1.6 it made 165 hp in the dyno..

[AdamOpheim]

An M90 supercharger used is super cheap and easy to find on marketplace or even ebay. MUCH more reliable and likely less than the $300 you spent! Best of luck tho!

[kellynull]

Get some stainless steel wire mesh and put between the supercharger and the intake to help keep the plastic from going into the engine.

[jameshathaway]

I put a amr500 and a 46mm Mikuni on my wifes 84 subaru GL. I loved it right up until it tore up all the front end drive components (ate the hubs and destroyed a shaft). It originally only had 76hp and the carb and SC are both rated to 150hp. Honestly I'm not sure what its making but the bottom end grunt is fantastic. Now I just have to retrofit modern knuckles and suspension into the old girl to get it back on the road.

[Sir_Leelord]

what about putting a screen between the supercharger and the intake so in case the fins shatter it won't mess up the motor.

[rionthaartist]

“While I am crazy, I am not insane.”😂 Same 💩 different day over here too guys💀

[Robreal-qihg]

Definitely favorite new channel you guys rock keep it up you guys don't get the credit you deserve twin turbo LETS GO

[cliffordplasd]

Here is a simple rule of thumb. The more friction the more heat, heat kills parts and power.

[duhwolf]

Raceland is the best bang for the buck. I put a full set on my XB and it corners like a dream.

[adammosher]

Don't forget to put window screen on the side that pushes the air in the motor so if it does fall apart your not getting pieces in the engine

[PrincessAddie]

Skip to the last 30 seconds of the video to see

[bradnunn]

Put a screen on the out put side. To prevent the problem from last attempt

[andychillin]

This is awesome I can’t wait for part 2! Definitely subscribing

[derpyyume]

Started watching thinking you had hundreds of thousands of subscribes not 5k! Keep up the good work!

[cdw]

so how is it working properly when its not pushing the air into the motor only towards the firewall?