HHO Dry Cell 9 Plate Homemade

preview_player
Показать описание
This is my homemade 9 plate hydrogen dry cell I made and is my own design.
4x4 stainless steel plates and homemade gaskets
I did the math and with the first bench test it produces about 0.8 LPM
The electrolyte solution is 3 tablespoons KOH to 1 gallon distilled water. About 1.18% KOH to water.
Plate configuration is as follows -NNN+NNN-
Рекомендации по теме
Комментарии
Автор

Cool, you have realized there are a few must do tricks to get best results !

RogerBuch
Автор

O.K. you've got the practical experience, which is more than I've got. good luck.

erikkristjansen
Автор

That’s an awesome looking rig there chief good job looks professional

MrSchoolmaster
Автор

This is good design but Where is oxygen outlet? Please explain .I am sure there is one .

samueljella
Автор

سلام ممنون از اموزش شما من میخوام اینجور دستگاه hho را درست کنم ومیخواهم با آن موتور 125cc را روشن کنم برای روشن کردن این موتورحداکثر چند صفحه لازم است و چه ماده ای برای جوشش بیشتر آب استفاده میکنید ممنون ❤❤

mehdigh
Автор

Wouldn't you get better output with one positive plate down the middle and TWO negatives on the outside, since the hydrogen comes from negative I would think it would produced more or am I wrong?

trashin.n.smashin
Автор

How do you know what size to make the plates? How does the exposed plate surface area affect the amount of HHO produced?

anthonypazoz
Автор

Do you know how to wire it to a 2018 Chevy truck. I got this kit from labellashho but their extremely rude on helping out. They got really bad customer service..plus their Manuel its
so hard to understand. A 3rd grader can draw it better.

sinuemedina
Автор

have to ever thought of a pulsed coil, at the entrance of the cell. The magnetize the air or water entering the system pulsed at a certain frequency, vibration ?

jasonspinmaster
Автор

How thick were the plates and which kind of stainless steel were they? Thanks!

jackmartin
Автор

What is the material b/w plates (rubber sheet type)
Where i can buy it

asadmanan
Автор

So with a dry cell, not quite sure how it works, the lines to either end of it both supply water to the electrodes, and allow gas to travel back up to the tank where the water is held?

bensullivan
Автор

hallo
im planing on makeing a 8 cell with 4 negative (-) and 4 positive, so its like positive, neagtive,  positive, neagtive,  positive, neagtive,  positive, neagtive...
will this work???

TheFilledk
Автор

Does it get hot?..If so insulate around those holes...100% silicone works..Home Depot..Makes less current loss..

RichardSmith-tnww
Автор

Nice job, I was wondering if you used fine mesh stainless steel screening you could increase the exposed surface area of the positive and negative plates . possibly making the cell more efficient?

erikkristjansen
Автор

what was the voltage between the plates?

johntingle
Автор

thank you very much
I liked your videos
We learn things.
Thank you

slimel-gharbi
Автор

What the max amperage it can handle???

ArthurPex
Автор

N what do u mean by nutral plate in hho-+-+-+ no any nutral palte

haroonahmed
Автор

IF YOU GET A CHANCE TRY USING 316TI AS THE POWER PLATES, 316L AS THE NEUTRALS, KOH, DISTILLED WATER, CCPWM. WATER WILL STAY CLEAN AFTER 8 MONTHS RUNNING

scagetman
welcome to shbcf.ru