SolidCAM iMachining Getting Started: The Tool definition and its effects on iMachining

preview_player
Показать описание
This is the fifth recording in Exercise #2 of a Getting Started series called iMachining of an Enclosure, where I'll cover the most common (need to know) topics about iMachining. In this video, I talk specifically about the Tool definition and its important parameters related to iMachining. Also shown is how the Wizard calculates the depths and what the importance of ACPs are when machining.
  1. SolidCAM & iMachining
  2. SolidCAM
  3. SolidWorks
  4. Milling
  5. SC2015 SP3
  6. SolidCAM Professor
Рекомендации по теме
SolidCAM iMachining Getting 0:11:42

SolidCAM iMachining Getting Started: Defining the CAM-Part and adding an iMachining operation

SolidCAM iMachining Getting 0:11:42

SolidCAM iMachining Getting Started: Defining the CAM-Part and adding an iMachining operation

SolidCAM iMachining Getting 0:06:01

SolidCAM iMachining Getting Started - Walkthrough: Define the machining of the center pocket

SolidCAM iMachining Getting 0:08:20

SolidCAM iMachining Getting Started - Walkthrough: Create and define the CAM-Part

SolidCAM iMachining Getting 0:08:20

SolidCAM iMachining Getting Started - Walkthrough: Create and define the CAM-Part

SolidCAM iMachining Getting 0:17:36

SolidCAM iMachining Getting Started: The Tool definition and its effects on iMachining

SolidCAM iMachining Getting 0:07:34

SolidCAM iMachining Getting Started - Walkthrough: Verify the tool path and generate GCode

SolidCAM iMachining Getting 0:14:06

SolidCAM iMachining Getting Started: Using the iMachining Technology Wizard

SolidCAM iMachining Getting 0:09:04

SolidCAM iMachining Getting Started - Walkthrough: Define the machining of the outside contour

SolidCAM iMachining Getting 0:11:35

SolidCAM iMachining Getting Started: Adding a new Machine and Material to the iDatabase

SolidCAM iMachining Getting 0:17:36

SolidCAM iMachining Getting Started: The Tool definition and its effects on iMachining

SolidCAM iMachining Getting 0:12:32

SolidCAM iMachining Getting Started: Using the iRest Technology type prior to finishing

SolidCAM iMachining Getting 0:07:34

SolidCAM iMachining Getting Started - Walkthrough: Verify the tool path and generate GCode

Intro to SolidCAM 0:16:20

Intro to SolidCAM iMachining

Getting Started with 0:09:57

Getting Started with SolidCAM iMachining - Video 1

SolidCAM iMachining Getting 0:02:33

SolidCAM iMachining Getting Started - 2D Example: Bottom ledge machining

Getting Started with 0:11:30

Getting Started with SolidCAM iMachining - Video 1

SolidCAM iMachining Getting 0:09:04

SolidCAM iMachining Getting Started - Walkthrough: Define the machining of the outside contour

SolidCAM iMachining Getting 0:02:34

SolidCAM iMachining Getting Started - 2D Example: Rough machining of angled surfaces

SolidCAM - Introduction 0:04:23

SolidCAM - Introduction to Imachining

SolidCAM iMachining Getting 0:02:13

SolidCAM iMachining Getting Started - 2D Example: Bottom face machining

SolidCAM iMachining Getting 0:12:32

SolidCAM iMachining Getting Started: Using the iRest Technology type prior to finishing

Getting Started with 0:11:30

Getting Started with SolidCAM iMachining - Video 1

SolidCAM iMachining Getting 0:06:16

SolidCAM iMachining Getting Started - Walkthrough: Define the machining of the pocket ledge

Комментарии
Автор

Hello. Crash with stock (round bosses in the centre) when machining open pockets at the bottom, even if I chose round bosses as the islands. You did not simulate these pockets. Thanks!

ВикторЯковлев-мя