DIY GUIDE : Small auto paint repair and CLEAR COAT BLEND

preview_player
Показать описание
In this episode, I'll share how to di a DIY spot paint repair and how to blend the clear coat. this is the simplest way to do a small repair on your bumper. I'll walk you through the process and share how to get the best results with this smart blend

SUPPORT THE CHANNEL
⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️

LIKE AND SHARE VIDEOS

SUBSCRIBE!

AFFILIATE LINKS!

COMMENT!

Follow us on Instagram and get the scoop on upcoming projects!

Follow us on Tik tok

Tools and materials used in this video. (affiliate links)
⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️

upol#9 fade out reducer

3m ultra fine 800 grit sanding sponge

sunmight flexible sandpaper 800 grit finish

Eagle flexible sandpaper interface pad

R500 lvlp paint gun for small compressors

upol 2k primer

low cost disposable cup system 1.0

astro sun light

premium tack cloths

prep solvent

raven latex gloves

finish1 fc710 with slow hardner

70% isopropyl alcohol

masking machine

18inch masking paper

3m performance masking tape 3/4

3m pps 2.0 cups , liner, lid kit

masking plastic

3m superfine sanding foam pad

video equipment I use
⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️

Go pro 7 black

Rode wireless go

Dji osmo action

Acer Nito 5 laptop

CHECK OUT MY OTHER HOW TO VIDEOS
⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️

Autobody repair made easy

how to prepare primer for paint

using body filler to repair a dent

How to repair body damage on your car

how to save a bad paint job

How to repair and paint your bumper

How to remove fisheyes from your paint job!

How to save a bad paint job

Disclaimer:
Due to factors beyond the control of Garage Noise, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Noise assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair video's. Due to factors beyond the control of Garage Noise, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again Any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Noise.
Рекомендации по теме
Комментарии
Автор

Glad I ran into this channel.. started my body tech journey in 2021 and I just got my first dealership job. Very helpful tips I’ll be using

damianpina
Автор

When I burn the clear, I put reducer in the clear. So the clear on the edges melts in and I like to sand it with 1500 grit sand paper. Buff the panel, for a better result. I mask the bumper does not matter how small the spot job is.

jamesmarques
Автор

Hey I used that UPOL blend #9 on the sail panel of my 1970 Charger RT as I did some body repair and then blend job on the upper sail panel of the car. I used some of this video as inspiration and partial guide when completing my repair. I had never done a blend job before but It worked out really nice! Thanks!

VegasRT
Автор

Customer got some free overspray. Im sure they appreciated it

joeycarpeal
Автор

Thanks a lot! I was fairly certain I knew how to do it, but I’m glad I watched this. I learned a couple of important steps. I’m grateful!

claytonmacnally
Автор

I’ve used the Spray Max Glamour 2K clear in a pinch a few times. You can swipe nozzles off of lots of other spray cans and see what works for a different spray pattern. I’ve found some narrow “bird shot”, and I’ve found the wide “shotgun spray” and that is key. But that Spray Max has serious longevity. I did my drivers side quarter panel, and it has withstood the gas spill test, sunshine test, the lot. Passes with flying colors. And it is hard. Not an easy scratch. The only problem is that while it last out glossy as can be and you can watch it melt into the previous stoke or coat, when it dries it’s gonna have some orange peel. Just spray several coats. I keep one of those infrared heaters about two feet away from the panel just as it’s finishing flashing off. Also a key factor. It also helps reduce orange peel. But it cuts out fine. For what it is, it’s incredible. You just can’t really prevent the orange peel.

andrewhigdon
Автор

Could you do this to cover a thin spot in a single stage paint job. The spot is about 2 inches x 1/2 inch.

Dale
Автор

With plastic bumpers you should be using an adhesion promoter so the paint doesn't peel.

catfishsnagger
Автор

Yes a big help for us DIY at home indeed cheers so much from Phil in Australia love the channel.

Snip
Автор

What makes Finish 1 710 and 720. 710 being spot panel and 720 overall different? Can you use them interchangeably?

frankmaceyka
Автор

You my friend are what Ive been looking for, truly great work, i have the exact same issue but on my hood

JayRosario-zvvt
Автор

Great video Chris with some really helpful advice for us DIY painters, this type of repair won't last as long as a bumper off and a full repaint but they are a good alternative and as you said it will last a good while👏👍John UK

JohnWDTC
Автор

How much time do you wait to spray on the blende and also time for polishing ? Steve

Steve-cstt
Автор

I used DA one day and burned thru clear coat (just a thin layer). Now it looks like I have a slightly of color dot on my paint that you can only see during a sunshine. What can you suggest? I’m also from Oklahoma

novi
Автор

So basically to make it look proper, full coat of clear ? Where does blend spray really come to proper uses ?

ogreunderbridge
Автор

I have a question when I spray the blend on how long do iI have to wait to buff it?

joshmirgan
Автор

Great video Chris!. Thanks.
Question regarding the settings.
What is general rule of adjusting these small touchup guns? What pressure should we keep for base and clear ? 20-30 or 10-15 ? How much fluid ? 1-2 turns out ? What typical distance -? Thanks 😊

Green_gtw
Автор

Sorry may be a silly question, is hobby airbrush possible to be used on this spot repair? What make me think using airbrush is hobby airbrush will spray more fine and suitable this area?

Jopakilo
Автор

it was very helpful, thanks for your time.

sd-zjdq
Автор

Great demonstration but you didn't say how long it was after the last claer coat blend before you Buffered up the rest of the panel?

nickevans