Nissan Altima & Maxima Front Wheel Hub and Bearing Replacement (07-18)

NISSAN ALTIMA 2007-2018 NISSAN MAXIMA 2009-2018
NISSAN MURANO 2009-2017 NISSAN PATHFINDER 2013-2017
NISSAN QUEST 2011 INFINITI JX35 2013
INFINITI QX60 2014-2017
This video will show you how I replaced the front wheel hub & bearing on a 2010 Nissan Altima. The hub & bearing is single piece integrated component held onto the steering knuckle with four bolts and the cv axle. This particular part is also used in other Nissan and Infiniti vehicles as noted in the beginning of the Description. An easy way to determine which bearing on the front end is worn out is by swerving the car to the left and right at speeds above 40 mph and listening for an increase in bearing noise. A right worn out bearing will make noise when swerving left and visa versa.

Parts & Tools:

Nissan Altima (07-12) Haynes Repair Manual

MOOG 513296 Wheel Bearing and Hub Assembly

TIMKEN HA590252 Wheel Bearing and Hub Assembly

Mevotech MB30301 Wheel Bearing and Hub Assembly

Milwaukee M18 FUEL 18-Volt Lithium-Ion Brushless Cordless 1/2 in. Impact Wrench with Friction Ring Kit with One 5.0Ah Batteries

Milwaukee 2855-20 18V Mid Torque, Low Profile Brushless Cordless 1/2" Impact Wrench with Friction Ring (Bare Tool)

CASOMAN 1/2" Drive x 32 mm Deep 6 PT Impact Socket, CR-MO, 1/2-inch Drive 6 Point Axle Nut Socket for Easy Removal of Axle Shaft Nuts

Mayhew Select 89082 Punch Set, 3-Piece, Black

Permatex 80078 Anti-Seize Lubricant with Brush Top Bottle, 8 oz.

Mayhew Pro 25076 1/2-Inch Knurled Brass Drift Punch

Glarks 555Pcs Heavy Duty Zinc Plated Cotter Pin Assortment Kit

As an Amazon associate, I earn from qualifying purchases. Thank you for your support!

#NISSANWHEELBEARING

[johnhines]

Finally a good video on DIY without a life story during the process. Great great great video my man. Thank you

[Streetlights]

Saved myself $900. Did the passenger side a couple months ago and did the driver side today. Thank you so much.

[frankguerin]

Great video! Helped a lot! I would suggest unbolting the ABS Sensor and removing it prior to removal of the hub assembly.

[gregsmith]

THANK YOU FOR BEING STRAIGHT TO THE POINT

[Afrattzz]

Great video as always! Glad to see you back. Removing the strut bolts is also my preferred method instead of messing with the lower ball joint.

[MultiSheniqua]

Great video I’m replacing my wheel hub bearings on my 2012 maxima this video was very informative thanks

[wesgibson]

Love the edit. Quick 6 min video instead of a half hour one. Exactly what kind of Milwaukee is that? I need that in my life.

[salvadorsepulveda]

Another great instructional video ! Your the man ! Happy Father's Day. Blessings 🙏

[balabay]

That strut looks new. That reminds me to replace my struts soon. I’m long overdue.

[jchock]

You are really good at your job. Thanks for sharing.

[gregraycher]

I didn’t release the strut last time I did it! I knew there was an easier way! Thanks!

[scottmurray]

Not trying to be a smart guy, Q: Why did you remove the CV and strut? I've done dozens and that was not required. Also, I recommend to NOT fully remove the 4 bolts for the hub assy, but loosen them out about a 1/4" or so and use a hammer to hit the bolt heads, thus pushing the hub assy out.

[timbowe]

U made dat look so easy i like the way u explain it so very well n easy. Out of all these so call handy man mechanic u was da best from start 2 finish. Good job 😊

[checkurhead_]

Great video. Thanks. No need for brass on the old bearing.

[autotemptleasing]

GREAT VIDEO NOW I HAVE ALL THE KNOWLEDGE STEP BY STEP....TO DO MINES

[earlyblackmz]

I have never seen someone so brave with antiseize before!! Great job

[Rick-wxmd]

Very well done. I have a 2017 that needs a new hub assembly. Thank you for the content.

[gregp]

I'm convinced, sending mine to the shop tomorrow. Good job but I bet my hub assembly will need lots of heat and a big hammer to remove. I'll spare myself the aggravation and pay a few hundred bucks.

[littlebittyducky]

Great video! Just finished mine. Just curious, did you use a new axle nut or use the same one?

[mikerockk]

Thank you for the video!! My passenger side 32mm is stuck on and I don’t have power tools, any recommendations? Thank you