Guide:Unboxing/Wiring/Firmware Installation of CB1&M8P(Voron 2.4 as an example)

👉 Hi all! The basic tutorial of installing CB1&M4P is released!Let's check what the instruction is !
⏰ Timestamps:
Unboxing & Introduction: 00:00
Mainboard wiring: 02:31
Firmware Installation: 05:16
Test & Print: 12:38

The stunning M8P has all the highlights of the 𝐎𝐂𝐓𝐎𝐏𝐔𝐒 but is even more COMPELLING! ✨
✅ Plug a CM4 or CB1 into the board for a complete solution that supports enhanced computation and connectivity required by Klipper.
✅ Supports both Klipper and Marlin
✅ 7 PWM fan ports( 3 Four-Pin fans+4 PWM fans ) with 24V/12V/5V voltage selection without using an external DC module. These make it easy to connect a watercooling kit.
✅ Displays supported: BIGTREETECH serial touch screen, SPI touch screen, LCD (EXP) touch screen.
✅ Configurable thermistor ports:5pcs 100K NTC OR 4pcs 100K NTC and 1 x PT 1000
✅ PT100 support with MAX31865(Optional)
✅ Equipped with 8 x motor driver interfaces(Up To 56V):
Motor0，Motor1，Motor2（Dual output），Motor3，Motor4，Motor5，Motor6，Motor7
✅ Drivers supported: TMC5160, TMC2209, TMC2225, TMC2226, TMC2208,TMC2130, ST820, LV8729, DRV8825, A4988.
✅ Proximity switch with 24V/12V/5V voltage selection to switch NPN and PNP probes.
✅ High performance MOSFET transistors on fans, bed and hotend.
✅ Overcurrent protection via the replaceable fuse.

CB1:
✅Tried and tested SoC - Allwinner H616 Quad-core ARM Cortex-A53 processor @1.5GHZ
✅ Affordable:The price will GET YOU A SHOCK!
✅ Supports Ubuntu with pre-packaged image that includes Klipper installation scripts.
✅ Pin compatible with the CM4 - 40 GPIO pins broken out using the identical BTB design used on the CM4 with similar alternate functions implemented to support use in 3D printing applications.
✅ Fast Ethernet + wireless LAN (2.4GHz)
✅ USB 2.0

🛒:
✨ CB1,Manta M4P/M8P:
✨ CB1+Pi4B :

[mathiasclarke]

Cool. Pleased make a Part 2 Video and Upgrade the Print head with CANbus.

[looxonline]

That's an interesting looking extruder ;)

[jamesh]

Could you please assist with a video or text file covering the steps required to configure the Manta M8P & CB1 to run the Hermit Crab Can Bus system as I can't find any documentation relevant to this anywhere
Many thanks for your assistance

[carlossalas]

Hola. no encuentro informacion de configurar dos motores un hotend mezclador, ejemplo para configurar pines y que no me tire error: "tipo de sensor" en klipper. gracias

[attic-Techno]

hello what is the way to run 60 leds on this motherboard

[petarbajai]

how about the adxl config is this possible with the cb1 ?

[mikelittlejohn]

Are you using a e3d hemera ? on voron 2.4

[TheDeathskull]

Ok but what does "Set to UART mean" really? You need to have written instructions with diagrams in the description. How do I know which jumper or pins do what? They are not labeled on the board.

[luismello]

Please create Manta with Canbus and eMMC

[ilyakrav]

There is no ability to directly upload firmware on the board?

[kf]

Isn't a 64 MHz CPU a bit slow to run a Voron 2.4? Mine even came with 0.9° steppers on A/B so double the required steprate.

[slor]

where do i buy the mounting bracket kit ( 2:10 ) ??!

[justanotheranonymous]

Does this board work with mach3 software?

[danhalai]

Can't read the text due to bad colour choice.

[EugeneSyvyk]

It does't matter how descriptive your video is on your opinion. If it doesn't have at least a simple voice over - it just sucks.
I'm no professional and I have very little experience with voice overs, but I'm sure I can do a good read that will add much more value to the viewer then this lullaby. Feel free to reach out to me for your next video. Voice over is a must have!