Installing a BENCH FACE VISE (HV516) and woodturning a HANDLE

Installing a FACE VISE on my homemade workbench :
(HV516) Making the FRONT JAW + INSTALLATION + Woodturning a HANDLE (plans) + Drilling BENCH DOG HOLES ...

HVQ516 has the same installation.

The Bench dogs came from 'Banggood' - "Drillpro Quick Release Bench Dogs".

Sound credits : Freesoundfreesound org

[mikepearson]

Absolutely excellent!
Perhaps the best and most concise description of how to install a face vice, of any site on You Tube
The diagrams, complete with your precision measurements, are an absolute treasure.
I'm much indebted to you.
This video saved me so much time and removed all the little doubts and uncertainties.
So fortunate for me that this was exactly the same model of vice I had bought!
But I believe your instructions would be applicable to many other makes and models.
Your description/measurements were easy to modify, to account for the minor differences in my bench dimensions.
You are to be applauded for your work. May you produce many more videos.
Obviously I instantly subscribed.
Thanks again.

[superhero]

I've watched several of these videos now prepping for my install. This is by far the best one.

[bluedragonfly]

Very cllear, easy to you, merci, danke!

[robertobrien]

without hyperbole. You literally saved my life

[GARDENER]

Just starting back into woodworking after 40 years & this was a great help in envisaging how to fit my vice.

Thanks.

[jahrap]

Nicely done, adding a single screw veritas to my bench, thanks for the great instructable!

[marleywellings]

Lovely stuff, I’m considering adding more dog holes along the whole width of the bench as to give a much wider clamping range. More holes always seem useful!

[berniesr]

That's a very handy video for me. Thanks for taking the time to make it.

[sfspencer]

Nicely done Mr. Steve. You are very precise and your explanations accurate and to the point. Good job on the diagrams as well. Thanks a million sir. Shawn Spencer

[gjoy]

Great video full of very insightful procedures explained clearly. Thank you for putting this together. I tried using the dimensions with a vise I bought from Grizzly. The vise looks identical to the one used in the video. However it seems like some dimensions are slightly off.

[musamor]

Thank you Steven for this very clear and concise video. The gentleman below, Mike Pearson, put my very thoughts into words.
Your video will be of great help to many. I have my old bench that I bought years ago. It has a Record 53 1/2 vise- extra large opening, but I'm still thinking of fixing one like yours- which I believe is German.. The Sjøberg Swedish vise is meant to be excellent too. If one could afford it, both the German Ulmia and the Swedish Sjøberg are dream machines to use, but there is still merit to making your own bench.
You have full marks from me. Your video is highly commendable.
Best greetings from France.
Ralph

[blackhorse]

I purchased two of same vices for my workbench and your video was of extreme value……… Thank you

[TarekElBaradie]

Thanks for the amazing detailed tutorial. Had a few laughs with the sound effects you added.

[Gazman]

After watching many bench face vice installation videos I think that yours was the best. Nice clean work. Well done.

[grzesiekk]

thank you man, it was very detailed and usefull. just both this type of vice and will be instaling it shortly

[RANDYSWORKSHOP]

I must give you a thump up for your detailed and accurate demonstration on how this vice is installed, excellent job...

[jeffhansman]

Excellent presentation and description. The sound effects work nicely too. Thanks for showing us your work!

[allenhess]

Great video. Thank You for providing the level of detail and measurements. This is very helpful depending on the level of the viewer and their need for information. Most of us don’t want to make things twice or to try to correct a mistake on a project like this. Your level of planning is useful, in fact necessary if you want to prevent mistakes.

[studio-beat-box]

This is the video I needed. Thanks for sharing. I have the exact same vise that will soon be added to my almost ready workbench.

[barryish]

Steven I am just waiting for the sparky to come and do the electrics to my new shed THANKYOU for this video it will surely help when I get to the vice. PS I have just