Holley EFI - Throttle Position Sensor Auto Set

Показать описание

Рекомендации по теме

Комментарии

these videos rock! I just got my hp system and would've never done this and bugged your tech line. please keep these videos coming, helps rookie "builders" like myself!

tundeclipse

Hello, I enjoyed this video, but I have a problem with calibrating the TPS sensor with a 90 mm cable that opened the gate. It does not respond to programming, whereas when the sensor is removed from the body of the gate and it appears that the calibration was completed on the gate, it indicates that the calibration was successful. This means that the wires are intact, but the motor does not work, knowing that the sensor is New and the portal opens completely. The application is on the LS3 6L. Is there an expected solution? Note that the general calibration file has not been changed, but only the firmware has been updated.

sniperpro_sa

Is it possible to make the throttle only open about 70% and use the auto-set to make it think it's at full throttle?
The 4150/900cfm is way to big for my mild V8 (should have gotten 2300).

ScottDLR

Only thing I get is code 19 does that mean?

paintballhallic

"slowly press the pedal to the floor, then slowly release the pedal. Do this twice" *stabs the peddle 2 times*

BoostedBoizKyle

I have a problem with mine, when I activate the clutch the AFR, A/F goes up to 22.0 to 26.0 and the engine dies, even with the engine hot this happens, does anyone have any tips?

JeanCarlos-tkej

I have an issue with my holley Dominator i using it on Gm turbo 2010 LS 5.3 GEN IV, x58 with LS3 TB DBW i used different pedals to keep matching between the pedal and throttle body as what was written in the holley DBW instructions i used Camaro 2013 pedal and Caddilac cts 2009 pedal the same pedal part number in the instruction when i did the autoset the throttle not opening after the preparing for press the pedal twice when i check in TPS vs. pedal table it's just reading 20% I dunno what the mistake or what the solution is there any special wiring for a pedal pin out or what ?

salimbinshagra

Holley EFI - Throttle Position Sensor Auto Set

Holley EFI - Throttle Position Sensor Auto Set

Sniper EFI Idle Tuning

Adjust Your Engine’s Response with Holley’s Sniper EFI Throttle Extension Lever

Every Holley Sniper NEEDS these two FREE Fixes! High idle and TPS not resetting FIXED!

What’s the Difference Between Holley Sniper 1 & Sniper 2 EFI Systems? | Summit Racing

Holley Terminator EFI Throttle Body Injection System for GM LS Engines

US Shift Throttle Position Sensor Kit Installation

Dyno Tested: Factory LS 90mm Drive-By-Wire Throttle Body vs Holley EFI 105mm

#holleyefi manual #throttle body setup part 1

Sniper EFI 92mm and 102mm Throttle Bodies

Holley TPS Kit Episode 444 Autorestomod

Holley EFI Billet LS 90, 95 & 105mm Throttle Bodies

1967 Turbo Camaro - Holley Sniper EFI Progresive Fixed Link Install & Test Drive

Terminator X Full Install and Overview

Auxiliary TPS for EFI installation

Cheaper #tps for Speedmasters $100 Throttle Position Sensor. #speedmaster #holley #nonamenationals

Holley EFI Billet Racing 105mm Throttle Bodies

TPS issue? Troubleshooting? Holley EFI Tips

How to TPS Auto-Set and Enable Static Timing to Check Ignition Timing with Holley EFI

Upgrade Your Classic Sniper EFI with our Sniper 2 EFI Conversion Kits | Holley Performance

Uncover the Mystery of Sniper Hanging Idle and TPS Throttle Position Creep!

Product Review Holley fuel Injection intake with Fuel rails and throttle body Terminator X LS 5.3L

How to Tune Holley Terminator X for Beginners - IDLE CONTROL TARGETS // Holley EFI Idle Tuning

How to: Holley Sniper IAC Position percentage adjustment. 1969 Pontiac Firebird 400