Troubleshooting Dishwasher Fuses and Control Boards - Whirlpool - Maytag - KitchenAid - Amana

Dishwasher not working? Discover how to locate and test fuses in your dishwasher with our detailed guide. We'll explore fuse and control board locations and show you how to use a multimeter for testing. The fuses protect the load circuits of the dishwasher. If one of the fuses blows it can cause the dishwasher to not heat, not wash, not drain, not fill with water, not power on, and more. This troubleshooting guide applies to Whirlpool, Maytag, Jenn Air, KitchenAid, Amana, Kenmore, and more. Find the problem with your dishwasher and get it fixed quickly!

Table of Contents:
0:00 - Intro
0:18 - Where To Purchase
0:26 - Reasons
0:38 - How to Remove
4:31 - Locating Model Tag
4:42 - How to Install
8:03 - Outro

Dishwasher shown in video: KDFE204EBL2

We sell OEM appliance parts for Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, Frigidaire, Electrolux, Tappan, Westinghouse, Kitchen Aid, Jenn Air, Bosch, LG, Samsung, and more.

If you found this video helpful, please click the thumbs up button and leave us a comment below.

Connecting with us:

#PartsDr #MakeAppliancesGreatAgain #Whirlpool

[PartsDr]

Did this help you fix your dishwasher? Let us know what symptoms and error code(s) you were experiencing.

[uhklem]

Very clear narrative and step-by-step images and instructions. Thank you!

[toma]

I misplaced the tech service sheet for my Kitchenaid dishwasher. Any way to find a copy online or buy another one?

[uhklem]

After a pump motor burned out a few months ago, and the heating element a month later, the dishwasher started stopping right after starting the wash cycle. Looks like replacing the control board fixed the problem. The old control board showed visible signs of overheating at the pump motor power connection.

[Mdeil]

My fuse blew a few months ago and got it replaced and since then it was fine. A few days ago it tripped again so I replaced it and ran it but maybe 20 minutes into a cycle it opened again. Do you think it may be a clogged filter that is causing the drain pump to work harder and blow the fuse? Guess it could be a bad heating element too.

[jjf]

The drain pump doesn’t pump the water out until I push in the middle of the door. Already replaced the drain pump, cleaned the drain hose and filter really well. Getting an F8E2 error code. Whirlpool WDTA50SAHZ0. Any ideas?

[JefeSr]

there are two fuses here, the f8 & f9. The f9 fuse appears on the schematic but I cannot identify what the f8 fuse serves. When testing the f8 fuse according to the diagram, it's open. I can't figure out what components are fed by f8

[lloydabbington]

My heating element burn out I replaced it, it's still not working so is it possible I have a bad fuse?

[johnlee-wcky]

Dishwasher circulation pump comes on and goes off during a session. Could that be a bad control board??

[horsez]

What if your service manual isnt there?

[RealMesaMike]

So, if the 50¢ fuse is bad, you have to toss the whole control board and buy a new one for $150.00.

Nice.

[shoodiemack]

If my power button to dishwasher wont even turn on then its probably my control board ... Right?

[marissahinds]

Both fuses are beeping from my multimeter test. I just replaced the pump and motor, but i am having a persistent issue of the water not circulating. Soap just drops and pools on the door and bottom pan. Do you think it could be the pump or motor wires? How do i test those?