Lesson 83: How to use 2 or more VL53L0X ToF Laser Distance Sensor

In this tutorial I am going to show you how to use two or more VL53L0X modules to measure distance using Arduino.

The best thank you for me is to not to skip ads and Subscribe 🔔 to my channel, like 👍 the video It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe and enable the bell 🔔.😊 .

Jump to different section of the video:
00:00 Start
00:50 Introduction
02: 55 Wiring Explained
06:05 Code explained
08:03 Demonstration

Purchase VL53L0X:

Related Videos:
How to use two or more VL523L0X modules: [this video]

Tutorial by Ahmad Shamshiri form Canada
****************************
****************************

Get other projects code and learn Arduino

**** AFFILIATE PROGRAM ****
#robojax #robojax_VL53L0X #robojax_sensor

[aerospace_andy]

thanks your video safed me quite some time!

[electronic]

You have shared useful information about laser sensors. thank you

[rlmccormick]

Nice video. Have you done any experiments to understand whether one sensor can interfere with the other? Any thoughts on whether there is a minimum distance you need to keep the two apart to keep them from interfering? Or is the deign of these sensors such that they are guaranteed not to interfere/crosstalk?

[maarten]

Mate your tutorial is right on time. Thanks a lot!

[nameerlatef]

I like all of your videos. I just have one question. Why do all the videos measure distance for you or for others? They do not approach small or precise distances, i.e. from zero to five centimetres. Are there such sensors? Please explain. Thank you.

[geoffwade]

Thank you this is very helpful for a project I’m working on.

[manuelsboarina]

Is it possible to connect multiple vl53l0x without using xshut? The sensor I'm using has only 4 pins: scl, sda, vvc and gnd

[RamonMoncada]

Really good video!
how can i work the same system on a Xiao Seedstudio RP2040?
ive having problems trying to adapt it

[rolandwiberg]

about the spatial resolution, what is the diameter of the beam hitting the surface ?

[robosapien]

Thank you so much! That's one of your best videos. Do you know how to change their i2c address, so that you don't need the multiplexer?

[sahil-ucfv]

Can we use this sensor in the presence of sunlight?

[barjjb]

Will it be possible with one vl53l0x and one vl53l1x with a proper code? Displaying results simultaneously on an I2C display?

[bottlefish]

I would like to know if they will interfere with each other when pointing at the same direction

[norsyahirah]

Hello Mr., how to adjust the code to have range?For example around range 0-40, Led will light up while above 41, Led will light out for 2 or more sensor

[melusisibanda]

Could you please show the connection configuration diagram for 3 sensors. I have been trying to use the example on the Adafuit library "VL53L0x_multi_extended" for my robotics project, but cannot figure out the wiring for 3 sensors.

[tiagodomas]

Please a video about how to connect a vl53l0x on a digispark (ATtiny )

[dalek-dan-]

what about resistors on the I2C buss when you connect multiple modules ?
Doesn't each module have resistors and having multiple will cause problems or not ?
Great video by the way, I was going to shut them down and only have one active at any one time, I didn't realise you could reassign athe I2C address which is really useful.
I assume this is lost on power off so will need to do at startup every time.

[oebleh]

So...got my TOF10120's they are great, but of no use for me now because there is no Pixhawk I2C driver in the moment. On arduino they are great..

[tenk]

Does this work if it's in a small space like a 5cm diameter tube

[soumitratewari]

Sir can you please make a video on lidar, how to use it.