Briggs and Stratton INTEK OHV Engine: CARBURETOR REBUILD & Repair. Riding Lawnmower LEAKING GAS FIX

Jeff's Little Engine Service shows you HOW TO remove, repair and rebuild a Briggs and Stratton 16.5 Horsepower INTEK OHV ENGINE WALBRO CARBURETOR. CARBURETOR LEAKING GAS: Float valve replaced and Fuel Inlet removed and replaced. SAME PROCEDURE FOR ALL MODEL INTEK OHV ENGINES!!!
Donations are greatly appreciated and help me make vids, just click the Paypal link below. Thanks!
Music by
Test Pilot - "Philadelphia"
Jeff is NOW Sponsored by GRIP tools! They help me help you! Check them out!
PLEASE KEEP IN MIND when you are watching my videos: I am showing you the least expensive, quickest "backyard" methods for repairing or servicing your lawnmower. Replacing all components such as gaskets and fuel lines is always recommended when rebuilding or repairing equipment. With these videos I hope you are able to fix and repair your lawnmower yourself with minimal parts, knowledge and tools. Thank you for watching!
Copyright 2016 Jeff's Little Engine Service

[deanwilliam]

I love that u give the sockets sizes. I was done in 10 minutes. Usually for me, finding the right tools takes longer then the repair.

[heru-deshet]

Purrs like a kitten. I love working on old cars and small engines that don't have computer systems to figure out. It's very calming. Nice job.

[PryseAuctions]

Thanks.. I couldnt see the flat spot on the solenoid but I saw how you did it and got the job done. Tractor runs great now after sitting for 4 years.

[KZEK]

Thanks for the video. I just removed the carb. from a Troy-Built with a BS 17.5HP 5002VV family engine. As I was sitting there in the pole barn think I should be video taping what I am doing so I could put it back with out a cup of screws left over! So Thank You very much for the insurance video.

[rearview]

Good video for those still using gasoline for fuel.  I had my 17.5 hp Briggs Intek engine professionally converted over to propane.  Best thing I ever did for my mower which is an eleven year old Yard Machine 42 inch cut.  I have about 68 hours on the engine running on propane and the engine looks like new because propane leaves no residue of any kind on the motor or any other place.  Starts and runs very well.  No more gas for me!!

[melissagarner]

The only video I could find that was same kind I've got thank you

[GHOOGLEMALE]

Thanks - That little choke lever I think is my prob but I can see how it goes now - Thanks, excellent vid well explained. Love the Rooster (but then I don't live next door haha)

[shhllc]

Excellent! Thank You.  I just bought a used Craftsman and need to do this repair I believe. I feel confident to try the repair myself. Again, Thank You. I will look for spark plug and other repairs.

[heatherjberg]

i am new to doing my own repairs and this video was perfect, thank you.

[netdoctor]

@ 7:28

I have that same B&S tool, but it's not very strong; I've bent it on the first use trying to remove an emulsification tube. Best find or make a special screwdriver that barely fits this bore, but will be stronger. I also have a #2 flat blade screwdriver bit, a long one, that i use with a 1/4" nutdriver, that works well. You just don't want to scrape away at the sides of the bore if you can avoid it.
Keep the B&S tool for lighter work or reassembly torque.

[stowers]

Very nice video, thanks a lot. This seems to be the same Carb that's on my John Deere D100. It's been running rough, and I'm not a Carburetor guy, so this video was exactly what I was needing. Much appreciated.

[ralonguyen]

Great video, thanks for taking the time to make it!

[ralopez]

one of the best explanations of how to repair, a carburetor ...Thank you

[luckydog-]

Super terrific tutorial ! Thank you for taking time to post it !

[JohnnyRFarmer]

Good video! Have two of these engines and only knew about half of what you showed. Thanks!

[chargerse]

Thanks for the tip on the fuel inlet fitting I have to replace 2 of those.

[MinhLe-vjij]

Thank you very much for sharing the information with us. I have problem with my ride mower but I did not where to seek for help. Sears they now closed. No where I can find help. You di help and I really appreciate. Again, thank you.

[michaelcaldwell]

You could use a torch tip cleaning tool for cleaning of the small holes, as the torch tip tool has different diameter rods that are file like .

[thierrydemey]

Hi Jeff from Belgium, nice video, thank you a lot! I've also this carb mounted on a briggs 20hp. Any idea for the replacing parts references? I'm looking for the bowl gasket ref and the jet reference, but i don't find them... :-/ Thank you in advance for your help 🙂

[Waffle_cones]

thanks. this just happens to be my exact engine and mine has carb. problems. thanks for posting!!