Kx 500 problems!!!! Help!!!!!!!

Got a fluid leaking out of my front sprocket that I do now know what it is ,Please someone tell me what it could be,Also I do not know the year of this bike ,If anyone knows let me know! :D ,Rate comment and sub :D

[MultiUnanimous]

Thank you for the suggestion, We replaced the countershaft seal and it fuxed it, but about 2 days after it got fixed and running my stepbrother blew up the engine ;/ lol

[MultiUnanimous]

Thanks man :D, Yeah we replaced the countershaft seal behind the front sprocket and it seemed to fix the problem, but After we got her running, I went for a ride on it (was a blast ) then I parked it and my stepbrother wanted to try it also and apparently he tried pinning the throttle fully open for 5-10 min in 4th gear to "blow out some carbon" so we got to do the top end now :/

[MultiUnanimous]

THanks man, I'll be sure to check out your bike on your channel, You just saved me some money ! lol

[MultiUnanimous]

Yeah that's how I feel, thanks for all the info on parts :D

[ALIVE]

lol. well when you rebuild it you should completly clean everything up and make it look nice and you will have a fresh bike

[howaboutdis]

Make sure the crank case vent is clear or it will happen again. Also keep an eye on the shifter seal. Ive had to replace both of em on my two kx's

[MultiUnanimous]

Yeah we are going to do a full restoration of the bike, Hopefully to get everything to original stock :D

[howaboutdis]

Oh yea make sure the crank case vent is clear or you will blow that seal or shifter seal again. Good luck buddy. :)

[howaboutdis]

Drain all fuel and clean the carb replace the fuel lines and put a new plug in it. I have two kx500's and i run 40-1 mix.

[MultiUnanimous]

Actually I just went and checked the bike, I put the kickstand back on the left side to see if it leaked again and either all the oil in my bike is empty (which it was drippng like a spout when I leaned it the first time ) I think the lube could have thickened up and is not dripping off the bike because it dropped a good 15 deg since I posted the vid

[brownpoop]

my rm 125 did the same exact leaking we fixed it by adjusting the floats in the carb

[MultiUnanimous]

Yeah I agree 100%, He could barely even start the bike when I bought it, I should have took it as a hint lol

[zXiXiRz]

its probably the oil seal behind the sprocket.

[MultiUnanimous]

Alright thanks bro I will do that, I'll actually record and post me doing it, Just to make sure I'm doing everything right xD

[cailll]

coutershaft sleave is cracked maybe behind the sproket, easy fix my 250 had that problem was greyish because of condensation maybe or just clutch residue

[apx]

That's in better condition than the one I got. I had among other things: no tail pipe, broken radiator mounts, loose fuel tank, no rad side panels, kickstart slippage, rear shock knackered, piston grooves deeper than a vinyl LP, nikasil plating on cylinder worn through, water pump gear missing, seat ripped etc. and i paid £900, but it runs fine now.

[kevinstearns]

theres an oring in front of the collar.

[MultiUnanimous]

It only dripped from the sprocket when it was leaned to the left, The carb looks like it's missing some hoses to me compared to my 125 but I'm just not sure

[MultiUnanimous]

I didn't fuck anything up, I bought it like that . I paid 700 for it and it ran, when I got it home and put it on the stand which leans it a bit to the right it started leaking, All it was was a countershaft seal . Literally like 6 dollar fix .

[mackiehughes]

its your countershaft seal its an easy fix