Setting your timing (marks) on your dual overhead cam on a DD15 and DD13

How to properly set the time on your DD15 and or DD13 dual overhead cam’s, I tried to make this as easy as possible.

[nervillerih-reh]

I felt like I was in college learning engineering. Plain and simple. You just got a follower. Thanks. Please do more, piece by piece for the entire engine.

[justinficarra]

I'm about to rebuild a DD15. I appreciate everything you've shown. Thanks.

[quocbinhduong-pvef]

engine detroit dd13_15 cascadia hả anh carlos, sao anh ko quay clip vậy anh.

[faheemahmedtanoli]

My mitsubishi truck won't start it also has a red engine check mark and its computer installed is broken they can't find it here

[xaav]

Are the both tools necessary ? After using the first tool , normally the two camshafts are well positionned ? where can i buy a similar tool useful to adjust the position of the 2 camshafts for an engine 4 cylinders Mercedes Atego EURO 6, TYPE OM934 ?

[marcelb]

Thanks, greatly appreciated.... 😎👍👍👍👍👍

[atm]

Hey Pedro, these 2 special tools that you have used them, I want to know from where I can buy them, bec. I am in egypt, or Can I make them with a specific lengths ? , plz help me if you can .

[supermariobronsmiranda]

Hey bro great videos man, just subscribed to your channel. Question im about to do the cam housing gasket. Of course im gonna pull the whole housing as one part. Now how would I set the timing with all the cams in place? Just rotate the flywheel? Let me add, ill be using the same timing tool, but with the flywheel pin. Thank you so much for your videos brother. God bless

[sonxairasakhamdee]

Hey brother I need some help!!
I did a Tune up valve adjustment
I clean my DPF
I change my Turbo Actuator
Oil change with all the filter, except the
fuel /water separator. Because it still ok.
Change fuel rail gasket
Change Delta port sensor/Calibrated!

My question is, how come I’m still getting same MPG without any differences what so ever.? The truck runs find. But after all that I would thought I would see some improvement you know. It’s a Cascadia Evolution 2015, 588750 miles. Thanks in advance for you time🙏🏼

[faheemahmedtanoli]

My truck's injectors and the 13d are from the engine's injectors

[diesellettuce]

I work on Cummins isx15 and 12 cm870 but I'm hoping I get to overhaul a dd15 soon. Everyone I know is scared of them I don't know why

[bundylovess]

Thanks for posting mate big thumbs up 👍

[djchankamixmaster]

Compre el timing tool en amazon y por una razon no se pone a tiempo quiciera saber si alguien sabe donde puedo conseguir uno que si travaje

No lo puedo poner a tiempo con esta de amazon y solo por barato 😢😢😢😢

[mposadalopez]

sr gear part number I'm looking for one but I don't have a sample

[maickcarpento]

Friend Pedro Fuentes in the USA, how much is the cost of a work manual and the cost of the tools to time and calibrate this type of motors?

[MrMaruvik]

Hi. Thank you for your video. Can you please explain or may be you have video how to check lash between the camshaft gear and idler gear with dial indicator? thank you.

[gulfmechanicalwork]

Sir me from saudi arbia
Pls tell me tappet setting what clearens set exust and england valve settin pls mm no

[ahmedeltawel]

Please dear friend how can i got one of this ?

[johnmensahkoffikoffi]

Hey bro nice video, So what about if I missed the timing and I have to set it again how will i gonna do it

[sergemaksim]

Hey great video I'm changing the housing gasket how do I adjust the gears