Toyota TPMS relearn procedure | Tech Minute

Andrew Markel explains the TPMS system on modern Toyota vehicles and why trusting the button may not be a good idea.

[DerangedAIJukebox]

Litetally nothing to do with the relearn procedure. Nice job 👍🏻

[major_fix]

I just wasted a minute and 32 seconds for him to tell me nothing

[PurpleSeaUrchen]

I love the part where he told me about the relearn procedure

[carcar]

you didn't explain how button works, no more donuts for you for a week!!!!

[Ammar]

Where does the main device located or installed in the car i don't mean the tire valve i mean the main device that get the signal from the valve?

[AngusNB]

Ah, I see. This is a sales pitch for something we don't need.
A tire sensor can't hide behind a caliper if you follow the instructions in your owner's manual.

REGISTER ID CODES
1. Press the tire pressure warning reset switch 3 times until the tire pressure warning light blinks slowly 3 times.
Then a message will be displayed on multi-information display. When registration is being performed, the tire pressure warning light will blink for approximately 1 minute then illuminate and “--” will be displayed for the inflation pressure of each tire on the multiinformation display.

2. Drive straight (with occasional left and right turns) at approximately 25 mph (40 km/h) or more for approximately 10 to 30 minutes.
Registration is complete when the tire pressure warning light turns off and the inflation pressure of each tire is displayed on the multi-information display.
Registration may take longer than approximately 30 minutes in certain situations, such as when the vehicle is stopped for a long time at traffic lights, etc.
After registering the ID codes, make sure to initialize the tire pressure warning system.

INITIALIZE the TPWS
1. Park the vehicle in a safe place and turn the engine switch off. Initialization cannot be performed while the vehicle is moving.

2. Adjust the tire inflation pressure to the specified cold tire inflation pressure level.
Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate
Based on this pressure level.

3. Turn the engine switch to the “ON” position.

4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks 3 times. (See illustration above)
A message is displayed on the multi-information display. Also, “--” is displayed for inflation pressure of each tire on the multi-information display while the tire pressure warning system determines the position.

5. Drive straight (with occasional left and right turns) at approximately 25 mph (40 km/h) or more for approximately 10 to 30 minutes. Initialization is complete when the position of each tire is determined and the inflation pressure of each tire is displayed on the multi-information display.
Initialization may take longer than approximately 30 minutes in certain situations, such as when the vehicle is stopped for a long time at traffic lights, etc.

[daveaaron]

My 2018 4Runner has no reset button, had to go to the dealership and pay $500 now it works

[terrytorres]

WHAT! He could of at least stood up for that 1min 31second of NOTHING!

[OlegOsovitskiy]

So relearn works only for the sensors already written to the system? And if I change my tires winter-summer it does nothing? That's exactly what I observe - this relearn button is BS, you need to write sensors IDs with the tool, no other options

[q-bert]

Hey thanks for nothing. The next time I don’t need anything, I’ll give you a call.

[keithbenson]

the relearn reassigns the wheel position after a rotation of previously registered tpms sensors

[donniev]

How's about explaining the process that is the topic of conversation?

[alwinkruijt]

Procedure : scan all tyresensor codes using ATEQ VT56 ODB2 scantool, Connect the tool to the ODB2 port of the car, upload the sensor readings.

[aluisious]

I'm not going to buy a separate tool just to swap to winter wheels.

[lucky-rowe]

If you are here for a 2020-2022 4Runner and have just had your first service the computer just needs some time to learn where the tires are now located. Do not watch this video --> you will learn nothing!!!!

[phaylithsouphithavong]

Your not really telling us how to do it in a vehicle!!

[autonomousglisteningwater]

useless. its just click bait to sell you something.

[theodoreother]

I'll act as the bs sensor, very strong signal. Nothing to do with title.

[ROGERDATTTS]

WTF did i just watched? Waste of youtube space

[nateblazejak]

Of all the millions of YouTube how-to videos this one is by far the worst