Chain and Sprocket Design Assembly and Motion Study : Solidworks Tutorial

--Real Motion--
Chain Sprocket Design Assembly and Motion Study Full Tutorial in Solidworks

The Tutorial Consists of:
1. Design
2. Assembly
3. Motion Study

Follow the tutorial from start to finish, you will be able to create such a real motion of Chain Sprocket by own.

1. Straight Chain Sprocket Design Assembly Motion Study Tutorial

Hope you Like it.
Do Share your opinions in the Comments.

Some Similar Tutorials:

1. Slat Chain Conveyor Design Assembly and Motion Study
2. Elevating Conveyor Design Assembly and Motion Study

1. PLAYLIST Solidworks Motion Study Tutorials (with Design and Assembly)

Thanks for Watching.
Do Like Subscribe and Share.

Stay Connected.

[muhammadalayyub]

When I mate the front plane of assembly and midplane of the links, the link moves away from the path?
Kindly give me a solution.

[jagatutor]

Wowo this realy good jobs brother. 😎😎😎
I like this tutorial 😎😎👍👍👍

[fn]

What if you have a fix center distance? How do you design the path with or without Chain Tensioner? I'd be happy to watch another video about this.

[Dharvin-toqq]

Can't select the 2 same circle when create nthe hinge...what to do...pls help me🥺🥺

[brouslikandor]

Hello pls can u send this assembly by email?

[zaidansari]

hello,
I am not getting motion analysis option I only get basic motion and animation. I did the simulation using basic motion but I got a very weird Result, Please Help

[GG-dgqt]

Hello, i need help with the last hinge joint, i cannot perform the last hinge joint as it appears with error, tried quite some times but still didn't work. Thank you.

[siddheshmahadik]

Number of new element states 3 doesn't match number of old ones, 4.

Such error is occurring while calculating.

[mikeomalley]

It won't let me change length of path. comes up with warnings that can't be entered. I have slowed down video and have draw it twice. Both times won't let me subtrcat without over defining???

[jhanolaer]

i want to know the formula of motion of the chain

[williamhensley]

59:34 What did you do different? You had just done the same mate a few moments earlier and it didn't work. Then you do it again and then it works. I have the same error as you got at 59:15.

Now I have them all constrained but now it still says it's under defined.

And now after repeating my save and rebuild, it says that it's fully defined.

[Akash-vsyh]

is there a relation between pitch and number of teeth?

[adityakandalkar]

chain is not rotating along the path as you shown in 15.29 what to do?

[satyaparida]

just great having lot of patience good job

[bassil]

thank yaa ma brotha from an otha mothaaa

[ximthdddyx]

I recently attempted to recreate this motion study in Solidworks 2021, but it didn't work quite as intended. There were a couple of settings that had to be slightly different compared to this video as they didn't exist. Also I had to use basic motion (Not sure if this makes a difference). the most I could achieve was that the sprockets wobbled back and forth slightly, and the links rattled and attempted to buckle. Would you have any suggestions for me to try / look at to correct this? - Hinge joint I couldn't select both sketches so tried concentric mate between roller and pins.
Apologies for the verbal diarrhea.

[NejinPokharel]

I tried so many times but for some reason I cannot make the hinge joint. Also, I cannot seem to perform any without deleting mate of top plane of the chain path and top plain of the assembly.

UPDATE: Flipping mate alignment in mid plane mates did the job for me. Firstly, I created hinge joint between each component even if it was over defined and deleted those which was unsolvable and the mate right next to those which were unsolvable and mated them again so that only overdefined error was showing. Then inside the mid plane folder, I flipped the alignment of any one unsolvable errored mate. Then wollah, every error disappeared

[MegaSahil]

@solidworks FUn sir ive to make a 55 teeth sprocket for my chain of pitch 12.7mm, but the polygon has only upto 40 sides max, can you please guide me how to make this sprocket?
i tried to make a 222.4604mm diameter construction circle and draw 55 lines of 12.70690863mm on it, but as soon as i try to equal it with the previous lines, the geometry gets error, please help im stuck here