RESOLVED: Ardupilot - Throttle not responding

preview_player
Показать описание
Under Radio Calibration, when moving the throttle stick I see movement. When moving the Throttle stick (under Servos) I get no response.
  1. kerry corcoran
  2. arduplane
  3. ardupilot
  4. skyhunter
  5. long range FPV
Рекомендации по теме
RESOLVED: Ardupilot - 0:00:31

RESOLVED: Ardupilot - Throttle not responding

Ardupilot throttle issue 0:00:15

Ardupilot throttle issue

ardupilot heli throttle 0:00:56

ardupilot heli throttle curve problem

Apm 2.5 no 0:01:28

Apm 2.5 no throttle response fix

Arduplane auto throttle 0:02:15

Arduplane auto throttle cutoff in RTL and Loitor mode : solved

Arducopter APM throttle 0:00:50

Arducopter APM throttle problem

Ardupilot FS Throttle 0:03:27

Ardupilot FS Throttle PWM Setting

When I Lower 0:01:26

When I Lower My Throttle My Quad Keeps Flying Away! Help! - FPV Questions

My DIY Flying 0:08:13

My DIY Flying Car Lifts a Lot of Weight (eVTOL) - Part 3

you have a 0:01:09

you have a trouble with arming in pixhawk ??this is the solution of it.

[FPV] First run 0:00:33

[FPV] First run of a new stack without capacitor. ESC goes BOOOM!

Configure Ardupilot on 0:02:07

Configure Ardupilot on Pixhawk to capture cruse speed / throttle for FFPID calibration.

Flashing Firmware - 0:00:15

Flashing Firmware - Arducopter - Click the link below to watch full video..

PixHawk, ESCs beeping 0:01:36

PixHawk, ESCs beeping problem, not responding to throttle

Drone throttle issue 0:00:34

Drone throttle issue

My Arducopter motors 0:06:59

My Arducopter motors are not spinning - Verify signal to motors

My Receiver Is 0:01:26

My Receiver Is Binding But It's Not Working! Help! - FPV Questions

PreArm Roll (RC1) 0:06:52

PreArm Roll (RC1) is not neutral solution || PreArm Roll RC1 is not neutral problem solved

Pixhawk drone Arming 0:11:57

Pixhawk drone Arming problem FIX #pixhawk #arming #problem #fixed #fix #drone #troubleshooting #diy

APM2.8 PreArm Check 0:01:57

APM2.8 PreArm Check FS_THR_VALUE Error Solved

APM 2.8 PreArm: 0:04:20

APM 2.8 PreArm: Need 3D Fix Problem [SOLVED] | Drone not Arming 100% solution Mission Planner

How to recover 0:00:33

How to recover from stall like a boss (Pixhawk Arduplane 3.5)

RTL over tree 0:02:30

RTL over tree no throttle, APM 2.5

Troubleshoot Drone Arming 0:03:02

Troubleshoot Drone Arming Issues with Mission Planner

Комментарии
Автор

::: RESOLVED :::
In Full Parameter List, I needed to change the SERVO1_FUNCTION to 4 (Aileron) and SERVO3_FUNCTION to 70 (throttle). Works fine now.

kerrycorcoran
Автор

Hi kerry, I have the exact 100 % situation like yours. When I checked the Full Parameter List, the SERVO1_FUNCTION to 4 (Aileron) and SERVO3_FUNCTION to 70 (throttle) is the default setting. But I still cant control the throttle in SERVO OUTPUT. Any idea whats the issues? Thanks.

boonchinx
Автор

Mate I got the same trouble. I use matek f405 wing and the latest version of ardupilot for the ar wing 900 build. I can change the servo1 output as Rc3 rather than throttle. Then I can move the moto good. But this situation no matter I armed or disarmed the fc. The throttle always can be start. Do you know how to fix it thank you

Nomoreseafood
Автор

hello, were you able to solve the problem? If so, how did you solve it?

ramazanbelyurt
Автор

You need to arm the Fc first bro, by full right rudder for 4 seconds. And by default it may have arming requirements, which you will need to set it to 0 first this test

EdwardChew