How To Reset Trailer ABS

By Pressing 6 times on brakes to reset ABS Sensor works for both Truck and Trailer. ABS Issue doesn't prevent you from driving BUT that is a Big Safety Concern and must be taken care of ASAP. Any law enforcement agency notices your ABS Malfunctioning, be sure you will be put Out of Service! There afterwards this repair will be quadrupled in cost. Take Care your equipment and Keep On Trucking. Good Luck Guys!

[chuckhurley]

Unplugged pig tail both ends...plugged back I..light came on. Then went out!! Nice job my man. Thanks!!

[InfamousTrucker]

Thanks for your help. Pressing the brakes 6 times worked for me. Great video.

[carolynwilliams]

Thank you I stopped on the road, look at your YouTube, disconnect my cable and everything is good thank you so much

[PNuttDaKing]

Honestly I just did the firm six times brake push and it actually worked . I’m in shock. Good job dude

[yasirmahmood]

Thanks mate you've saved me from being towed back to yard. thanx u

[tiborhorvath]

You are correct, it’s worked. Don’t turn on ignition before pumping brake pedal.

[davidmichalovych]

Thank You Brother . I followed your first step and it worked .

[masonwilliams]

Wow, I unplugged electric cable and replugged it and it worked. Thanks 4 the info😎👍

[KingGrippySocks]

What brake pedal? The brake pedal in my truck shoukent have any control over the issue with a trailer? How do you clear it without whatever youre talking about?

[Ajay-rwjy]

Thanks bro! Just pumped the brakes and it cleared i appreciate your video!!!

[pyatt]

Unplug, replug green cable.
Apply brakes hard 6 times to reset

[mouasetoure]

Same thing happened to me and I did exactly what you said. And then I’m good to go. Very good video. Thank you 🙏🏾 !

[ernestoveliz]

Awesome tip, it worked, two thumbs up for you my friend!

[shanesmith]

Great advice, the brake pumps worked for me!!!! Thanks

[markvanwormerjr]

Pumping the breaks actually worked. Hell yeah.

[dplsus]

After doing the last step it came off. Thank u!

[hookahb]

Lol...Un plug the pig tail, and plug it back in...Thats it found usually that never gets it..However you can take your pig tail lose from the trailer, and check the pig with your light detector..Hook your alligator clips to a good metal surface and probe to check the power is going thru..Also important to go back under the trailer..Find the wire that runs into your drum on each inside wheel...Feel along that wire near the wheel and you will find a plug, thats the ABS plug...It easily unplugs..Take some starting fluid if you have it, and shoot a little in the plug, and the 2 pins on the other end if you have some..Starting fluid is a great way to clean electrical connections because it drys super fast because of the alcohol, and cleans things up pretty good..Next take a wire brush or sand paper and scrub the little pins..Then add a small dab of grease on each pin, and plug it back in..Do this on all 4...Its simple and easy, and is the problem most of the ..Dirt and corrosion gets in there, and it just needs to be cleaned up..Now go back and start your truck..Hopefully the ABS light is now gone...If all else fails put a little electric tape over the tattle tail light and haul ass....LOL

[fifteendollarbill]

You shouldn't just be looking to clear the light. You should be looking for the problem that caused the light to come on in the first place. Don't juat turn the light off and ignore it. So the light is off but the underlying problem is still there

[alexovXX]

Thank you! It worked for me on second press

[dantedanis]

I cut my abs light and attach the cable to clearance light and now it is working 😊