How to Bind with Flysky Receivers - iA6, X6B, iA6B, Fli14+, GT3B, FLIT10 - FS-i6 and FS-i6X Radio

Need to bind your Flysky receiver to your Flysky transmitter? This video is for you! I'll show you the two MOST COMMON methods of binding that will apply to almost ANY receiver! I'm using the FS-X6B and FS-iA6 receivers as examples for binding with the FS-i6 transmitter (AKA radio).
In case you're wondering what BINDING is, binding is like a "virtual handshake" between your receiver (Rx) and your transmitter (Tx), and is required before you can use the receiver. This way your transmitter will "remember" the receiver and automatically "pair" with it every time you fly.
*NOTE: My bad, GT3B is a transmitter and GR3B is the receiver.

Quadcopter receivers:
FLIT10 (not recommended)
Airplane receivers:

Buy through these links to support the channel:

-------
MY GEAR

FILMING GEAR

--------
Mandatory Disclaimer:
I participate in the Amazon Affiliates program, which means that if you click on one of the above Amazon links and purchase a product on Amazon, I will receive a teeny tiny commission (at no additional cost to you). Also, various other links listed here may be affiliate links, to which this disclaimer also applies.

**REMEMBER, always use caution and your best judgement when building and flying RC aircraft, be a good neighbor, and HAVE FUN!**
-----------

About this channel: Adam makes FUN and HELPFUL videos about building and flying Radio Controlled aircraft, tech, and DIY projects!

[MARLIELEPPO]

Could you make tutorial how to setup ibus on i6, you have video on i6x only! (for betaflight)

[raiyanbashir]

how to bind fs i4x(tx) with fs r6b(rx) im in trouble ! please help me

[taylang]

This was great I would rank this number 1 of all RC tutorials. Keep up the good work!

[UrsulaKender]

I use a FlySky FS-i6X Tx and FS-iA6B Rx for my model sailboat. I would like to collect control data (PWM) using a second FlySky Rx connected to an Arduino and datalogger. Is there any way to simultaneously bind two receivers to a single transmitter? I also have FS-GR3E and FS2A=4CH receivers available. Thanks.

[tomlatimer]

Adam, to say I could use your help is a huge understatement. I bought a heavy duty, all steel hydraulic loader from an online auction. It came with no paperwork, no instructions, and I'm totally new to this. Upon playing around trying to figure it out, I could only get the bucket to raise and lower. thinking there must be a problem with channels synced between receiver and controller, I chose the factory reset option, big mistake I know now. Ive been doing a ton of reading, and watching videos, about all of yours, so I think I have a grasp of what needs to be done. Doing it not so much. everything i have watched regarding binding the two, the receiver is out of the truck, plane, etc. Can I bind the two with the receiver in the loader? taking it out looks problematic. I have made a jumper bind wire, put it on with heat shrink protection from touching the center terminal. Can I now bind with the FlySky FS-I6S? If so, how? The receiver is a FS-IA10B. 2nd question, would you be willing to help me set the remote controller up? I am reaching out to you here, I am new to this so not sure where would be best. I need help bad! And it would be greatly appreciated! Tom

[The-Warm-voice]

hi bro how you done i watched this great video but i need your help i have radio control FS 10ch i6s white i use him on my rc truck with battery 3s 4200mAh 35c but when the battery is weak and the truck move slowly the battery still full on my radio screen i think she needs adjust from RX set up
high volteg 6.0
alarm volteg 4.2
low volteg.4.0
i think she adjust from this settings until to reading right if you have any idea i hope tell me that thx dude

[ltcolsin]

I knw the video is 2019 but my power supply is a Li-poly RC Battery 7.4V 8C 2000 mAh, and the wire lay out is red- white and black so is that going to be a problem?

[anmwolfrc]

I need your help with an rc helicopter and a new transmitter and a receiver you help me PLEASE this is transmitter and receiver FlySky FS-i6X Transmitter and FS-X6B Receiver
can and will I be able to use it on my Blade 130s rc helicopter and how

[MrSaccoccio]

Adam I have a RTR truck that is all set up, but when I went to power up the radio it was junk. I bought another radio same model and style and went to bind the new radio to the same receiver and the receiver would not stay on.. something is amiss can you help please!!!

[FloridaWildlife]

Getting a bind but no servo action. I tried 2 different receivers and same thing.

[ebsigma]

hi, i hav a FS-i6 controller, i want a full kit to use the controller and build cars and planes and whatever comes to mind with the 3d printer and such...
I know that FS-iA6 or similar is needed, but I would like to know what other components are needed (battery and its charger, something to be able to put an fpv camera... and others.
thz

[hudmel]

I have the Xiangtat Flysky FS-X8B Receiver and I bind my remote to it and go into beta flight and I go to receiver and I give throttle and nothing happens. Just build the drone tryo 79 anyhelp?

[annikinmendoza]

Does it matter what lipo battery it is or no because I was thinking of doing for the fs-16x controller to use a 6.4 volt battery to bind to the controller.

[creeperjoypeqce]

Thx man you made my day, thank god because of you I succeed on this😁

[resadrecebli]

İ have fly sky fsi4 and A6 receiver
When i try to bind the slowly flashing red light not changing into steady light. Any solutions?

[lucadagani]

Ciao volevo un informazione.... è possibile accoppiamento tra TX fly Sky e RX radio link
Mi puoi aiutare grazie

[michaelcoppola]

Help! adam I reversed channel one on the controller now i can' t reverse it back . i have followed the instruction the switch looks flipped but its not. I am using this on a sailboat for the main sail control. Down should bring the sail in and up should let the sail out . i reset the controller defaults and followed your instruction to rebind the receiver.

[tedwells]

Hi,
Can I set up a second receiver to work with the same transmitter? 1 Tx to 2 Rx?

[morinryudojo]

I have a fly ski T6 remote and I'm trying to bind a FS ia6 receiver can you help me with this

[eddiemanuelitonavarro]

Can I bind my FS-T6 transmitter to my FS-iA6B reciever?