Unfortunately a big fail today with NASA fabric #3dprinting #shorts

preview_player
Показать описание

  1. Aero
Рекомендации по теме
Unfortunately a big 0:00:59

Unfortunately a big fail today with NASA fabric #3dprinting #shorts

Our Cameras Capture 0:00:10

Our Cameras Capture Everything…Unfortunately. #Shorts

unfortunately fail to 0:00:15

unfortunately fail to catch big one fish#fishing #fail#shortvideo #shorts #viral #top #beauty

Ooops 😝😝🤣, unfortunately 0:00:12

Ooops 😝😝🤣, unfortunately it happened, #shorts #fail #funny #fails #fails

New Years Cake 0:00:10

New Years Cake Fail With Unfortunate Message || ViralHog

Unfortunately injuries are 0:00:29

Unfortunately injuries are part of it 🤕 #gymnastics #gymnast #injury #injuries #sports #olympics

UNFORTUNATE LOGO DESIGN 0:00:17

UNFORTUNATE LOGO DESIGN

Unfortunately I did 0:00:13

Unfortunately I did not make the Olympics #sports #shorts #gymnast #olympics

That's unfortunate 😬 0:00:08

That's unfortunate 😬 | #shorts

Unfortunate girl crashes 0:00:09

Unfortunate girl crashes quad bike #fail #quadbike #shorts

#ocean Replying to 0:00:14

#ocean Replying to @slothmymango Unfortunately that's the open ocean #shark #oce

It is Impossible 0:00:19

It is Impossible to Stop This Unfortunate Accident

One of my 0:00:16

One of my biggest shrimp died today unfortunately #shrimptank #shorts

Lots of unfortunate 0:00:20

Lots of unfortunate falls at Badminton, luckily both horse and rider were fine

Unfortunate way to 0:00:12

Unfortunate way to fail. #roblox #gaming #shorts #backrooms #robloxhorror

Was This Unfortunate 0:00:08

Was This Unfortunate or Fortnites Biggest FAIL?

The Unfortunate Truth 0:00:20

The Unfortunate Truth About Today's Society and Women #datingadvice

Unfortunately it’s a 0:00:09

Unfortunately it’s a lie

Woman Had An 0:00:15

Woman Had An Unfortunate Accident While Snow Tubing

The kitten tried 0:00:09

The kitten tried to jump, but unfortunately, failed again.#Shorts

UNFORTUNATE EVENTS 0:00:08

UNFORTUNATE EVENTS

Julio's Unfortunate Mishap: 0:00:17

Julio's Unfortunate Mishap: A Wedding Party Cake Disaster to Remember

The Unfortunate Problem 0:09:08

The Unfortunate Problem With The Rings of Power

The most unfortunately 0:00:16

The most unfortunately real post ever

Комментарии
Автор

You mught wanna check to see if your nozzle is clean, sometimes debris can get stuck and cause issues like this. You may also wanna check your printer and model settings to make sure that they're taking the nozzle size into account.

mememan
Автор

I suggest using the .4 but adjust the print diameter in the slicer. That most often works way better than just getting a whole new nozzle!!👍👍

wyattduncan
Автор

I tried for 3 days non stop to print a massive full sheet on my Neptune 3 Max. Totalled about 1000 hexagons. First layer took over 3 hours. Took 2.5 days of failed prints to even get a full first layer because of tiny irregularities of bed leveling. Then at layers 5 or 6, a section started pulling off the build plate and I tried my best to glue them back on but had to give up. I might be able to get it with a few more tries but I just didn't have the heart to try anymore

VoidOperator
Автор

I printed it on my p1p and it took 4.7 hours

AdonaiBuckner
Автор

My .2 on my A1 mini has had a miserable time. Fraught trying to clear it for 3 hours today.

ThingsYouMightLike
Автор

It might be your printbed, you did change it out recently

landonlove
Автор

Your voice is super similar to Brendan Robinson! The guy who plays lucas on pretty little liars lol

abbystarheart
Автор

Bet it was the speed the made it fail. I tired printing with a .2 and had to drop the speed down a lot about 30-40 mm/s to get it to stick then sped up to about 60 @ about 205-210'

UndertakerTx