How to put Fisher & Paykel into diagnosis mode

preview_player
Показать описание
Putting the washing machine into this mode will cause the machine to stop retrying and fault straight away when it finds a fault. This is so that time isn't wasted and a clear indication of the failure can be obtained straight away. Refer to the user manual located here, to see what your error code corresponds to.
Рекомендации по теме
Комментарии
Автор

Oh wow this actully worked!!!! We had a recent power outage and my ancient fisher & paykel machine was just doing craxy beeps and not going...its now working wahoo thank you and God! As he led me to your page❤

katrinalodge
Автор

Figured out a few things that people will find helpful:
1. When you turn the machine off after this, you're actually switching between ON, and this flashing light mode, there is no longer an OFF. But read 2 now:
2. That low level light.. just press it down again to turn it back on. This will let you turn it all back off when you press the power button. It's just a lock for staying in diagnostic mode or not.
3. Most of the other buttons do stuff which change which lights are on.. I *THINK* it's set up custom tests.. Don't if press water temperature buttons (it will just start pouring water in, hot or cold as pressed) if your machine ain't draining lol!
4. It looks like the Spin Speed buttons switch between modes, which it remembers when you go back to it!! Mine was originally flashing all the same as the guy's in the video, but I can't
get it back to that. You can't put the level low light back on in some of those modes, in order to exit and turn it off, but you can definitely get back to a mode where you can. Like learning a new watch.

After experimenting with that, and trying to get to just spin and drain, Play just puts the lid-locked light on (it isn't locked though). @SadamFlu how am I doing so far? :)

ToninFightsEntropy
Автор

It worked for my Fisher and Paykel Washmart.. thank you.

deepikadear
Автор

My start/pause button is worn out. Can you recommend a tutorial to replace the touch panel? I am having trouble removing the facia within which its mounted, there are 2 screws that release it and allow it to pivot up an inch, however I am unable to remove it or pivot it enough to remove the board or check the specs to order the new part.

tommo
Автор

Thankyou! Does it take long to give you a diagnosis? My machine seems to be taking a long time

stevejenningshealthcoach
Автор

OK then what do we do how do I get my washing machine to start up again?

ladymarie
Автор

I had to go through this a couple of times but it worked and washer seems to be working. I think when the power came back on after a brief outage, it messed up the cycle even though the washer wasn't on at the time it was still plugged in.

reneemullins
Автор

Have you got a video on how to unclog the drain pipe for this machine?

faloisv
Автор

What happens after I put it in diag. mode and it flashes for 5min and goes blank. I get not error code and there is definitely something wrong with my machine?

janicecassista
Автор

So i get 1 light coming on, then i push power and it changes. Is the first the error code or the second.

matty
Автор

Always getting a cold wash. Not getting a full tank of hot water when Hot is selected on my F/P GWL11 Washer. Have replaced Hot Water Valve, and new Thermostat. Still not working. If I select Hot, the Washer begins the wash cycle with hot water, (this is a short cycle to wet cloths & dissolve soap? Not sure?) but then when it begins the volume fill the water is stone cold. Same with Warm setting. Any ideas?

dougdoug
Автор

do you know how long it normally takes? I've been waiting 5 minutes :/

rebekadunn
Автор

I have an Elba washer and dryer bought them both in 2009. My washer is acting funny the wash cycle is shorter now it only takes like 15 minutes to wash in (all Modes) and also noticed that its not filling the tank with water it just dispense water but in the same time it drains it. Does that sound NORMAL to u?

roxanastoica
Автор

SadamFlu, I put my Fisher Paykal into diagnostic mode and the first 5 lights left to right are blinking. 1&2 yellow, 3, 4, 5 green. What happens is I power on and then is starts and stops. Water on then off about 12 times and then it stops and beeps continuously. Since I've had this since 2002, I've had a few parts replaced. It's been such a dependable machine. Should I fix it? will it last another 10 years? Thanks for any help. Sharon

sharonm.wasileski
Автор

The machine is working except the door can not close so it makes the water keeps running out due to the door not locked.

RuthAJoseph-ys
Автор

Renee Snijder clean your water hose intake filters at the back of the machine. Where the hot and cold hoses screw on. They are removable to clean.Most likely not the actual valves, just crap from the water supply.

judysummers
Автор

I have no power to my Fisher and Paykel, it stopped during a wash any suggestions

jodieheath
Автор

does this work for a Frigidaire gentle Annie? if not does any one now how to put one into diagnostic mode.

niallsullivan
Автор

my washing machine lights always flash like that after Every load what does it mean tho

bekzmika
Автор

My power light won't come on .No power to the machine.

louisphillips