CWI Exam II

This video is more information on what is on the AWS Certified Welding Inspector exam. It goes over Skewed T-Joints, Responsibilities, Groove Weld face reinforcement, and it contains a list of every question that was on all three parts of the exam when I took it a little more than a month ago. Thanks for watching and subscribing to TVWeld.

[patrickclark]

Brother Im going to school highlighting the book trying too take it all in. Everything your teaching is helping so much and I find that my school does not provide this same info . very informative and extremely helpful. Thank you.

[TVWeld]

The only other thing that I forgot to put on there is weld access holes.  I bet there was 5 questions on weld access holes on this test.  Many on thickness requirements.  Make sure you know where to find weld access holes in the code section.  I think they are on page 200.

[bigbird]

Thanks dude! I'm watching all your vids

[jasonhale]

Hey Brent, I recently read that the members of AWS seemed think that the 2010 Part B didn't have anything on pipe inspection and deemed it unfair to the pipe welders. Well I took the exams today and just to say I hope they don't start feeling sorry for people jumping off of cliffs. If so we will not have an AWS board period, 95% of the Part B inspection test refers to or is inspection of pipe

[johnnyorsojr.]

I took the exam back in February. 72% on part b, 75 on fundamentals, and 66 on code. I studied fundamentals for almost a year and still scored low. Needless to say that I didn't have a 72 overall and am taking it again in Ohio at the Hobart Welding Institute. My biggest problem was time management and navigating the books. I wasn't knowledgeable about the code part because I didn't know the exams so extensive. Man it took me a month before I was mentally ready to pick up my books again

[compxci]

a resistance to applied forces so if the Z is small, the resistances will be less?? Apply energy, force to a system of two in this case, to cause a fracture cannot happen if the Z spacing is within a spec??

[MumbereDerick-wsrq]

am also doing welding and fabrication but I don't have a book of welding now how can I get it Sir

[domesdomes]

Brent -
On Part A was most of the questions from the WIT book.
Part B was it the sample blocks that need to be measured.
Part C was all questions from D1.1 code book.

In the D1.1 code book you said in one of your videos that half the book won't be on the test. Can you tell what half would not be on D1.1?

1 more month getting nervous.

Great Videos...

Thanks, Rich

[alanakaaadabossharris]

Brent does the online cwi pre coarse help for the final test?

[devlonmx]

Brend, Might explain how to use procedures prequalified as fit up

[keloidguy]

do all the closed book questions come out off the d1.1?

[vietnguyen-ehjm]

Brent Harkness
Thank you so much for your sharing :D

[jeremyparker]

Sir, I’m looking for study material for specifications, and drawings ( part b) possibly heat treat charts

[jasonhale]

Brent, have you talked to anyone that has taken the newly revised CWI exam with the 2015 D1.1 code?

[drewtaylor]

Taking d.1.1 test here in nov. I also am taking the week long pre course seminar and had the online seminar for 2 months now. My question is should I wait till my classes to highlight and tab out my d.1.1 book? Or ok to start now? Just did not want to mark it all up with useless info that I wont need

[bld]

Ok so being 2018... which book should i get to study for the test? I have almost 15 years welding experience but my knowledge overal was pretty specific to the jobs ive had. Predominantly pipe, 100% xray high pressure vessels. So i definitely need some education!!! I am not able to travel for the week of seminars. So i will have to do it from home. And then take the tests. Although they do provide online classes for $2000 buck now....

[compxci]

what is a Z loss, is this in any way related to Impedance used in energy studies??

[sreeuttamkumardas]

Dear sir,
Have a good day. How to get these books? Please give me this information.

[ironpimp]

hi Brent, I took my CWI test in sept of 2016, part a got an 87% part b 50% and d 1.1 I got a 88% well since my overall % was lower than 72% I have to re do all the test, that part b killed me bad, I took a course at a private inspection school and I guess I didn't get part b down, is there anything out there to help me out to explain the part b better? I'll be taking it in may again, you did a great job on the 2 videos you should do one on part b as well