Matlab Simulink - Ansys Simplorer (Twin Builder) - Maxwell co-simulation

This video is a step by step guide to setup a co-simulation between Ansys Maxwell, Simplorer (now known as Twin Builder) and Matlab Simulink. With this tutorial you can do electromagnetic simulation in Maxwell with a control algorithm, however complex it might be, from Simulink.

[anirbannanda]

Extremely good tutorial. I'll recommend this to everyone. It will very useful for anyone wanting to do co-simulation.

[debotrinyasur]

Thank you dada for this insightful video....was waiting for the next one especially after the drawings in latex video..

[esijal]

Excellent and informative presentation 🙏

[moinuddinshaikh]

Very Helpful sir..!
THANK YOU VERY MUCH!!!💯

[KHMakerD]

Thank you so much for the tutorial. Very helpful.

[vinaykumarnainapatruni]

Thank you so much sir, I was struggling from past 1 week and this video helps me a lot and I should say that it is very clearly understandable. You got a new subscriber😁

[nitishsharma]

really on this topic i found first video @saptarshi dey

[animeshshaw]

Hi Saptarshi,
Greet work. Thanks for the video.
can you please make another tutorial on how to link Ansys maxwell with MatLab for Motor simulations.

[RitaMattar-wx]

Thank you for the informative video. I would like to know if there is a way to do the same co-simulation but with a simulink building block instead of an S function.
I couldnt find the information anywhere

[peymanmogh]

Very helpful sir👍🏻. Wish you explain how to build buck converter in the Ansys. Thank you 🙏🏻

[henrikjohansson]

Thank you a lot for the great tutorial! 
I run into problems though at the SiM2SiM part where I get error ".aedt is locked and cannot be opened". I saw you also had the buck.aedt.lock file active when loading the Simplorer circuit into Simulink but didn't get any error.
I tested closing my Simplorer buck circuit file but then nothing happens instead when I try to load it in SiM2SiM. Also, when I reopen it, I no longer find my Transformer Maxwell project in the Project Manager of the Buck Simplorer file but the component is still loaded and connected in the circuit. Not sure if that is a problem or not?
Do you know what could be the issue regarding SiM2SiM and how it could be solved? I use Matlab R2020a and Ansys Electronics Desktop 2021R2.
Best regards

[ktWVN]

how can i add output of maxwell is Force ?? not I or U

[Dev_Nishabd]

Can u make more tutorials on co-simulation with simplorer

[vaibhavsinghgaharwar]

thanx for the video sir...sir how to connect fluent with MATLAB for real time co-simulation? plz help me..

[AshishGupta-tdlx]

Hello, Good work. Will this also work for Electrostatic simulation? Also, any idea how I can integrate MATLAB script & Ansys MAxwell 3D without Twin Builder? Thanks!!

[soumyarupasaha]

Can we add more than 1 simulink blocks in one single system of the simplorer

[exempli]

Great video mate
Do you happen to know about this error
[Sim2000]Error 10532- Error encounter while PREPARE.>>CLOSE
It pops up just as analyse the simulink circuit. Can't get my head around this

[supriyanaik]

Hello sir, do you knowledge about how to do optimization in Ansys after calling in MATLAB?

[moyukhmandal]

Thank you for this valuable tutorial. I tried this for Axial PMSM . But show error in S-function. I check all in and out pin link, try with simple simple simulation file but same think appear. Pls help me to identify where was the problem.

[abdelbgd]

Hello, thank you for the vidéo, i want to co-simulate a pmsm like this if you can help me please.