How to Measure Ride Height | Steeda Tech Tip

In this video, Team Steeda gives a technical overview of measuring and implementing ride height to your specific taste. Throughout the video, we will breakdown each component that needs to be taken into consideration to properly getting your Mustang or Ford vehicle to its perfect stance. We also go over how different shock absorbers will impact how your vehicle's stance sits and the ride quality. Be sure to stay for the entire video to get the complete lesson on vehicle ride height!

Purchase these parts directly from Steeda:

---

Steeda Website:

Steeda Performance Vehicles

Steeda Europe:

Steeda Pinterest:

Steeda Facebook:

Steeda Instagram:

Steeda Twitter:

Steeda Blog:

#RideHeight #MeasuringVehicleRideHeight #Steeda

[et]

You guys are hands down my favorite after market company. My 2016 GT now has pro-active shocks, billet shock mounts, sway bars w/ end links, Bumpstop /Jounce Kit, polyurethane vertical links, IRS Subframe Bushing Support System, h-pipe, and an Ultralite 2-Point G-Trac Brace. Handles and sounds amazing now

[emilepapillon]

lowkey vid telling all there is to know about suspension adjustment !! No bs, very objective. Thanks for the great content.

[biggrigg]

I installed the steeda springs, billet vertical links, adjustable control arms on my gt350, it sits better and rides alot better, now i need to order the sway bars

[pooincognito]

how to fix a car leaning on driver side when observed from front. which part of suspension is more likely to have damaged. can you make a video on that please?

[moisesflavia]

Excelente video y muy explicativo. Me sacó de dudas sobre la instalación de las suspensiones a mi vehículo. Well done 👏👏👏

[ClaytonYatescarenthusiast]

Apex sticker nice! Took the good wheels off and put those mmr wheels on.

[NjBoriG]

Wish u talked about more how to adjust the height. U just did 1 part which was how to measure. What about on the strut? Or on the coilover?

[edwardjohnson]

What is the ride higth of 2002 ford taurous?

[teckniec]

"You are getting a little bit goofy or obsessed corner to corner".
Me who installed new coil overs and noticed all corners dropped by a quarter inch after a week, which is normal, but the left side front and rear dropped by a millimeter more. Now I am watching videos about ride height.

[TrackDayVideo]

Just ordered irs support and cross brace for my Gt350r

[anthonymcelevey]

My Ute has new coilovers & it's leaning down on the drivers rear corner, I lowered the car but they're all set equal pedders extreme XA adjustable coilovers they fit them & I told em about it Leaning they reckon it's normal. I had to raise that corner 8mm to get it level, now opposite front corner is lower than the other side ??

[cognac]

I have the rearward springs matched to the front . When I have a passanger the rear passanger side drops 2/16 and the driver side rear goes down 1/16 but when I get into the car also the rear driver side then matches, goes to 2/16 . Anyways. My question is do I lift the car in the rear 2/16's more .. so that when we are in the car the car is now level in the rear with the front..but anyways it would always be 2/16 higher in the rear. If Iift it 2/16 more, But normal when driving completely level.. Seems we need a full tank of gas and weights in the driver seats. Cause. Seems 1/16 is like around 100 pounds. 2/16 I'm guessing around 200 pounds

[nicolebraxton]

Do you measure it the same way as the front like you measure the rear with the tape measure?

[bilaltariq]

Hi if the ride heights are different on each wheel and you don’t adjust the preload on the anti roll bars can the measured pressures in each tyre be different even if they have the same amount of air? I keep putting 35psi in at the petrol station and a day later one wheel has around 31 and the other 37

[antwon]

Would it be bad to try to put 20s on a 3.7 v6 with 18s stocks I just ordered xxrs for front and back but I wanted to leave my stock springs on my car

[kevingomez]

What shop would you recommend in So Cal?

[roadracing]

There's a lot easier way to find static heights. Asking guys to loosely find the center of the wheel induces error. Measure from the wheel lip at the bottom of the wheel up to the fender edge.

[thedude]

What does Steeda recommend for camber settings for street use?

[josedionicio]

Love dose wheels. What brand are they.?

[bumpcage]

Ride heights should be made with a "Trim Height rule" to get an accurate measurement.