120w + 120w TPA3116 D2 Stereo Amplifier Board | Bluetooth Amplifier

120w + 120w TPA3116 D2 Stereo Amplifier Board

Unboxing, connection and test

------------------
Using Comments -
TPA3116d2 Amplifier board
Bluetooth module
Power supply
8 inch woofer
6 inch speaker
7805 IC with Heat sink
________________

TPA3116 D2 Amplifier Board

 Bluetooth 4.1 MP3 WAV Decoding Board

24v 5A power supply

Bluetooth Module

 ______________

Please like video and Share
Thanks for watching | Have a good day
------------------------------------

Please Subscribe to get more interesting videos:-

-------------------------------------------

Facebook page
------------------------------------

All Playlist videos -

Creative Ideas-

DIY Ideas and Life hacks -

Electronics Project -

Unboxing and Test

Solar project -

--------------------------------------------------

#TPA3116D2
#BlutoothAmplifier
#SInfinitycreative

[trinidadgoonzalez]

Muy buen amplificador buena instrucción pregunta el módulo MP3 debe ser mudo o con audio yo triny

[andrea]

hi, I have a vintage car with the original amplifier. For you will be possible to use this board just for amplifiing the output of the existing amplifier? i mean, in thethe 3 wires connection ( input of the board) can i connect the speaker output off the old amplifier in series??

[likiyeah]

Hi, I bought a Tpa3116d2 bluetooth, and I connected a Grunding Audiorama 4000 to it. It splits the eardrums and has some crazy bass. Bye bye

[lucasazevedo]

Friend ask me a question please, I'm building a sound and I intend to connect 4 5 inch speakers of 25rms each 8ohm, and I'm in doubt on which source to use, do you think a 12v and 10 amp switching source would work for pull the sound quietly?

[kakacdsoficial]

Só tem 50w x 2 conforme o datashet em 24v

[sebidsouza]

Don't stepdown the same supply to 5 volt use different 5 volt supply or use mobile charger to power usb module it will remove unwanted noise

[stalker]

To avoid extraneous noise, it is necessary to break the "earth loop". In the bluetooth module, it is necessary to unsolder the resistor with zero resistance in the GND-AGND circuit.

[jesustadeosanchezarzeta]

Yo traigo el mismo equipo en mi vocho pero no supe que bocinas ponerle

[josuegomez]

Yo tengo el mismo y nunca me imaginé que fuera tan potente me levanto por canal 2 bajos es un par de 15" y otro de 10" y si los mueve bastante decente y también su par de medios agudos y super agudos y le tengo de fuente de sonido un ecualizador sansuy y es perfecto para este mini amplificador hace retumbar la casa con un sonido de muchísima calidad creo que el ecualizador le sube la calidad es un buen amplificador lo tengo conectado a 23, 2v y 25 mil microfaradios en capacitores y jala bien

[Sumitlifts]

Boom box banane ke liye acha hai kya kit?

[CrzzAlpha]

Question, how does the wattage go? Is it increased as well?

[javymolina]

Por qué le entra mucho ruido, es por la fuente o es por la etapa del Bluetooth ? Es un ruido residual, por favor explícame

[jonyhereis]

I got this amp runing with an 18v 3.5 a laptop power supply cord and it sounds amazing. I'm using a mono mp3 module and i dont get that noise

[d.i.y.ak]

I am supplying 12v 1.5 amp DC. When I increase the vol. The power led starts blinking and the amplifier do not work properly. Please help

[audiokees]

I do miss low bass with this tda7498 chip. sounds very raw.

[Jayasoorian]

Whether I can give 3+3 parallel speakers (8ohms per channel)?

[rafaelrivera]

A este amplificador le puedo instalar un torna mesa ?

[RixtronixLAB]

Nice video, like it, thanks for sharing :)

[davidpazdera]

Nice setup I bought the board but I can not find the Bluetooth BT-max anywhere the item was not available on Amazon. Do you know where I can find it?

[expertblue]

deben poner parlante o woofer del mismo tamaño, nunca diferentes tamaños y mucho menos de diferentes impedancias ni vatajes