The Secret To Perfect Segmented Rings

In this video I discuss how I use my wedgie sled to create perfect segmented rings. ↓↓↓↓Click here to show more below ↓↓↓↓

Wedge Templates for setting angle on your wedgie sled.

If you'd like to help support my YouTube channel there are some things you can do that don't cost you a thing. First you can subscribe to my channel and make sure you hit the little bell so you get a notification when I upload a new video. Another great way is to be sure and give the video a thumbs up, leave a comment below in the comment section and share the video on your social media. And finally you can use my Amazon affiliate links down below when shopping on Amazon. Thank you so much for your support

Thank you.

Use Discount Code dave10 to receive 10% off your Ack's order.

Dave's Social Media Links
Twitter: @DaveGatton
Instagram: davegatton

#Bowlturning #Woodturning #Lathe

[cornwasher]

Boy, this video answers the problems associated with getting segments to fit properly. Thanks a million.

[Jonboy]

one of the finest tutorials I've seen cutting segments. Plain, simple but very meaningful tips. Thank you for sharing. Just wish you could ship to the uk😢Regards, Tony.

[timgarner]

Thanks for sharing! I have been doing segmented rings for a bit and have had trouble getting tight joints. Now I learned how to do it! Thanks, Dave!

[richardgerhard]

Nice quick and brief video. Of the segmented videos I've seen, you're the only one that included the tip with the wedgie board, to start with the forward fence for the first cut. Had my lathe about four years now, still a newbie.

[FranklinWoodWorks]

Wow. Been doing segments for a long time, and still learned something new. Well done Dave!

[ljgault]

I always wondered how folks made those segmented rings now I know. Thanks Dave.

[ovenordhaug]

A valuable contribution for us novice segment turners. Thank you!

[daveb.misc.]

That explains it Dave! Ive never done any segmented pieces, because i didnt think i could get them to fit together tightly. I might end up trying it one of these days! Thanks!

[ThePapa]

Some great tips Dave. I just talked about the line on top yesterday but did no mention the one on the side. I stopped using that one because as long as I have the already cut edge toward the blade and line up that takes care of it. But when first starting out both lines will help.
You should always use the side of the fence that is away from you so the blade is not trying to push the work away from it. With expensive wood I will hot glue a scrap to the end so I end up using all I can from the good stuff.
Glad you put this out as a stand alone video because it clears it up very weill.
Take care,
Gary

[graemeross]

Another way to get an accurate angle between the guides is to lift the jig up to the vertical. Place a digital angle gauge on the lower fence and set to zero. Move the DAG to the top fence and set the angle. This is very accurate as long as the jig is vertical and allows any angle to be set. I made my jig from scrap perspex.(nice and stable) Great video as always Cheers Graeme

[aypepa]

Clear and simple explanation! Thanx a mil!
My only concern is that the grain in your segments is not along the axis of rotation. Does the wood chip?

[AndrewJacksonSE]

Thanks Dave. My segmented bowl making has been hugely frustrating with fit of pieces.

[scottbionicnerf]

Thank You Sir for very helpful hints on how safely make these rings.

[johnguarino]

Thanks, very helpful video. I’m just starting to make some segmented bowls and the guidance you’ve provided is great.

[billm]

Thanks for that good tip Dave! 👍🏻 I’ve been cutting some out and I didn’t mark them! 😞 Have more to cut tomorrow and I’ll mark those! Also I’m using your templates!Thank you for sharing!

[sunbladerr]

Great Information.Thank you. At the end I spotted the extra wedge that is on your zero clearance surface plate. I will make use of your techniques. Be Well and Good Journey Richie.

[TheTdeline]

Great job Dave. You explain the process with great detail. I'm going to have to build one of these jig and purchase your templates at your online store.👍

[tonyprofera]

Well then! That was truly helpful and a great tutorial Thanks for sharing it with us! You are a rock star!

[jimbennett]

Great safety tip - thanks for sharing!!

[sheldonpangburn]

I still keep running into problems where the length of the segment grows as i cut it. Any suggestions on what to adjust? im using a micromiter gauge with an offset block clamped to a fence. digital calipers to dial in length of segment.