DIY Camshaft Welding/ Grinding

preview_player
Показать описание
Thank you guys for watching!

Make sure to like and subscribe!

Also, follow Cave Troll Forge Co on Facebook and Instagram

Related Articles:
  1. Cave Troll Forge Co.
Рекомендации по теме
DIY Camshaft Welding/ 0:05:21

DIY Camshaft Welding/ Grinding

Hardface welding on 0:03:06

Hardface welding on MGB camshaft Deltacam.com

Cutting out hard 0:01:57

Cutting out hard face weld on Honda Cam

CRITICAL Lesson For 0:10:01

CRITICAL Lesson For The Home Engine Builder- MORE Camshaft QC Issues To Wreck Your Day

Camshaft - High 0:05:36

Camshaft - High Lift and Duration - Increase Horsepower

repair and change 0:00:55

repair and change camshaft profiles with welding techniques #shorts

welding of a 0:03:48

welding of a cold chilled cast iron cb350/4 camshaft

potong cam yg 0:00:30

potong cam yg sudah makan welding buat baru

Engine block transformation 0:00:12

Engine block transformation after chemical dipping

DIY sprocket tool 0:05:12

DIY sprocket tool - BMW Mini single camshaft - No welding required!

Mesin Camshaft welding 0:00:35

Mesin Camshaft welding by JMW motorsports

Cast iron camshaft 0:01:34

Cast iron camshaft welding DeltaCam.com

Welding a crankshaft 0:00:07

Welding a crankshaft before we grind it

APCAM b16a camshaft 0:00:49

APCAM b16a camshaft welding

camshaft welding build 0:01:01

camshaft welding build up for boat racing 32mm to 36 mm #shorts

camshaft welding 0:00:16

camshaft welding

How to Rebuild 0:01:00

How to Rebuild Broken Crankshaft with Amazing Welding Technique (Part 2)

Welding Cam Shaft 0:00:30

Welding Cam Shaft wave

Tapered Shaft to 0:06:24

Tapered Shaft to Straight with Angle Grinder GENERATOR ENGINE

Particle Spray Welding: 0:00:11

Particle Spray Welding: A Promising New Technology for Camshaft Repair ||Technological Wonder .

How to Resurface 0:03:06

How to Resurface a Cylinder Head at Home

cam profile build 0:00:09

cam profile build up and machining.. #music #automobile #mechancial #dancehallmusic #welding

BUTT WELDING FLASH 0:01:00

BUTT WELDING FLASH GRINDING

Anodize Your Parts 0:01:00

Anodize Your Parts at Home

Комментарии
Автор

iv tried doing this but was a bit more slack. only had a stick welder with mild rods and no blow torch to burn out the oil. didn't do any proper measurements of the lobes but made sure the timing wasn't too much off. added about 2mm of lift and made the exhaust have a longer duration. have had the motor running and has a lot better response once tuned. still need to mount it to a mower and test it under load. nice work with the editing for being new btw

droptheblades
Автор

I'm working on a bodge jet boat, have the jet drive but it can only take 25~7 hp so will be doing this to a 420cc cam, + a carb and take the governor off it should be around 20hp~ ish i hope.

samuelforsyth
Автор

How long did it last? Was it a runner

jamesgravel
Автор

What is the result of this modification? Did you start the engine?

cirilovac
Автор

You need to install different springs to bring the valves back plus new and stronger seats, waste of time

egjorgov
Автор

Your intro music is three times louder than your voice. Why do so many people do this? You aren't making friends by blasting people's eardrums.

sammorgan