Brother 8810dw replacing the fuser

Could be similar to 8710dw and 8910dw

[KMayflower]

Two 50 year old women used this video to install a new fuser on a Brother MFC-8710DW in 20 minutes with just a screw driver!!Thank you for the great video, we couldn't have done it without it!!

[stevesikora]

Thanks for the step-by-step demonstration of both disassembly and reassembly. It helped me get over a couple of areas where the parts seemed to be too tight, so I thought I was doing something wrong. I changed the fuser unit since the print coming out blurry and would jam sometimes. Everything works well now and the print is crisp like before.

[yichunzeeck]

I am have still using ur video after all these years. Please keep it on YouTube. Thank you

[jaredsavino]

Thanks for the video! This video also applies to the Brother MFC-8950DW. Just followed this video while replacing the fuser on my 8950.

[jcolonjr]

Invaluable video! Our fuser has needed replacing three times (the ONLY thing that has gone bad on this printer) and all three times I've used this video. THANK YOU for recording and sharing!UPDATE: Now it's been 4 times this video has helped! This Brother printer has outworked our past Kyocera & Xerox!

[TheRealLaughingGravy]

Thanks so much. I just did this with an MFC-8910DW, and the parts and procedure are the same. The parts came out easily but went back in with much more difficulty because everything is black inside. It was very helpful to have this video to refer to.

[sharond]

Thank you! I did it! Saved myself big bucks on a nearly new printer with fuser issues.

[sherridyer]

You are my hero.  Saved me a ton of $$ and I have my printer working perfectly again.  Many thanks.

[Ilovenygal]

Thanks for taking the time to post this. I was able to replace my fuser with no problem! :)

[paulv]

Thanks for posting this. Fixed it myself no problem with your video!

[SainatoChiropractic]

Thanks for the video - replaced fuser for MFC-88719DW - thank you again for posting

[SPARTANsui]

Video was very helpful, thanks for taking the time to make it.

[josueparra]

Donde consigo la guia de plastico blanco que quitas antes de sacar el fuser que esta a tu lado izquierdo se me quebro

[popsyk]

just open and close the front door concerning the nylon latch, and the fuser cover has 2 notches

[ramonperera]

I need to get to the power supply board on an MCF L2700DW. It does not turn on after a lightning. I do not know how to open the panels to get there. Please help. Thanks in advance,


Ramon Perera.

[gmm]

UENOS DIAS OJALA ME PUEDAS AYUDAR TENGO MFC 8950 IGUAL COMO LA DEL VIDEO. EL DETALLE QUE FUNCIONABA BIEN Y DE PRONTO ME DICE QUE CAMBIE EL TONER. ENTONCES YA SE LO CAMBIE Y EL MENSAJE ME SIGUE APARECIENDO, YA CAMBIE COMO 3 TONER NUEVOS DIFERENTES YA HASTA CAMBIE EL DRUMMM COMPLETO Y AUN ME SIGUE APARECIENDO EL MENSAJE ME DICE " CAMBIE EL TONER AQUE SE DEBE O CUAL ERROR PODRIA HACER AYUDAME

[HendryTabisari]

There's a jammed paper in the rear off mfc8910dw help me remove it

[christopherdouglas]

I busted the little spring with my ham fists will it still work or is that a ground?

[emilarnest]

thanks too much it very nice it is help me

[tundratekk]

Where can i order a fuser for my Brother 8710dw unit?