Huge Current MOTOR DRIVER BTS7960

Huge DC Motors ( 2 wire) can be easily controlled using this BTS7960 Module.

[mopenstein]

This is 100% how to wire this board. I just duplicated it on a raspberry pi and it worked perfectly. Don't believe the writing on the board, follow the directions laid out here. Thank you for the video!

[whitneydesignlabs]

Great video. Thanks for the explanation. I am going to be using 6 of these controller to control wheelchair motors in a 6 wheel drive "Mars" style rocker-bogie robot.

[tanjiro]

Best Indian Content 💯
Just Subscribed, Love u❤️

[livefreeordie]

How would you add an encoder to this, to control position, speed and direction? And what type of encoder would you use IE magnetic, photo cell etc? Nobody seems to make a 24V 350W large geared DC motor like the one you used in this video.

[josephjojo]

Excellent explanation, Sir. Can you mention of any controller like this that can handle two high-current motors same time?

[BarMagnet]

Can this driver be used to drive a transformer winding to produce a decent inverter?

[DrFailov]

I doing similar things but getting my Arduino constantly rebooting once motor is powered. Power is stable, something with noize or I don't know

[DNATV]

How many motors can be use on adruino?

[gersonfer]

What happens if I set the enable pin with a value different of HIGH or LOW ? For exmaole if I set it with a value of 150 ?

[chennojurahuldev]

With the connection, my motor is not changing the direction(anti clockwise). I cross checked the code & connections thrice.

[VentusFPV]

I have burned 3 of those.. with 350W 24V wheelchair motors. From what I have learned this cloud be because of back current. This driver does not have protection from back current. I will experiment next with cytron mdds30. Should be better.

[nikonikolic]

Hello, how do i use the low-side MOSFET inside the BTN8982 when the load (Motor) is connected to the Vs + supply (+24 Volts) and O/P terminal (tab and pin 4)? I'm using a PWM drive signal at the input of IN while INH is held high (logic +5volts)? The datasheet shows that to select either the high-side or low side MOSFET transistors inside the BTN8982 will mean that when the PWM signal is high (+5 volt level) then the high-side MOSFET will be on therefore shunting the motor which will act a brake, which is not efficient? Any ideas?

[vitalii]

Hello, can you help me, please?:) Can i use PSU on 20v, and motor on 12v? Or i need use and motor and PSU on 12v? Thank you veru much for answer

[khelifihebbache]

Bonjour cher monsieur, est ce que deux moteurs de 12 volts comme les vôtres peuvent faire marcher un robot de 40 kilogrammes.

[ThuongPham-dndh]

Really appreciate your work for this video !

[gazzat]

Hi Saravanan,

Read with interest this article and I'm still not sure how it works.
How toaActivate the high and low side mosfets to drive the motor.
For simplicity, say I didn't want to use an Arduino { I'm to old to starting code} but simply drive the inputs with +5volts.
If I enable say the l/h chip {INH High} then apply a high to {IN} how do I enable the r/h chip so that the lower mosfet is connected to ground and assuming the l/h chip the top mosfet is connected to the supply rail.
Does it mean that on the r/h chip I enable it {INH High}, will that in turn, turn on the lower mosfet with {IN} low.

I'm at a loss.

Can you help
Thanks
gazza

[messengerofgod]

Excellant demo, but what about the Arduino coding for us who can not do the coding. Blessings

[guruv]

hi sir,
can you please suggest 4 channel bldc motor controller which can be used for 1500w bldc motors

[reynertuazon]

Is it that module not getting hotter for a long time use ?

[weekendatgarage]

Hello,
I have connect ibt bts7960 to wiper motor snd flysky remote control but some time working to move left side and right side and some time moving to one side only, really i dont know how to fix that