Programming A Marantec Remote - How to Program Additional Remotes to Marantec Garage Door Opener

In this video we go over how to program an additional remote to your Marantec garage door operator. We also offer tips on programming the remote and how to determine if you have the correct remote.

Purchase Marantec Remotes
Purchase Marantec 3-Prong Programming Connector

If you don't already have one remote programmed into the operator then you'll need to do that first. Here are the links to the instructions on how to program that first remote. After you do that, then come back and watch this video on how to program additional remotes:

Models:

[davidcollins]

greatest, simplest explanation ever. if you have the correct new remote and follow the instructions it's a 20 second job to program the new one. Worked like a charm.

[SpartanThreeSeven]

Thank you! I picked up a replacement Marantec 382 from a local garage door company and this video was spot on. There were no specific instructions regarding this procedure. The replacement remote came with the 3-prong connector, so I was able to get them up and working within minutes. Cheers!

[UnderstandingPsalm]

We bought remotes on amazon after confirming we had a 315MHZ and this video worked great. We didn’t have remotes so we watched the other video on how to program the first one. The lights were a bit different on our but it still got it done. Thank you.

[flameheart]

Viewed your tutorial and fixed the issues with the second receiver coding. I could not code the second receiver but once l put the prong on the opposite side of both receivers it worked. So thank you for your tips, you gave me better advice than the place where my garage door has been serviced and saved me $$$.

[AlixDeyling]

I was all prepared for this to be difficult. You made it so easy. Thank you thank you thank you!

[emedikon]

On my remotes, there was no flashing of the lights on the remote that needed programming, just a steady light, but it still worked.

[elizabethkeller]

Your video is very clear. My new remote, however, does not blink when I press when connected to my existing remote. It’s a solid red light…and does not program. Any suggestions?

[samharrison]

I have a question. Are you able to program both the top and bottom button to control the same garage door? When I am going to use the garage door remote I tend to just randomly click one of the buttons. That doesn’t seem to work here.

[Will-ifwp]

Is there no way to use universal genie remotes with my marentec garage door opener? Whenever I get one working, the others don’t work.

[Taryn-vuvl]

How do i connect a genie remote to a marantec 260 series also i lost my remote that is programmed

[steveoneway]

Is there a way to do this without the programming 3-pronged device?

[kellyclemenson]

Good Morning, I purchased a replacement remote, the program connector fits properly in my existing remote but is loose on the new remote ?

[spirosdalianis]

Hello! Thanks for the great video. I have programmed 2 controllers, but the 3rd I tried, start blinking as soon as i insert the three pins connector (not connected to the master remote). Do you know a way to reset the controller? Thanks

[mike]

Clear as mud. Why replace this and that with the programmed and the new one.

[nobodyaround]

Thanks. What is the second button for?

[christinasanchez]

My renter took the control. I don’t have any original remotes. What can do?

[El_Cheapo]

Does it matter if the programmed remote is at the left or right? I want to make sure I insert the programming connector at the correct side to transfer the code.

[angelomasannat]

If u have old use to work can reprogramming it I tried didn't work

[vocalone]

How do I get all four of these four-button remotes working again?

I have the 4-button remote to work all four-door openers. One door opener will not work with but one remote at a time now after my wife's remote quit working her door. I had replaced the battery first(nothing) so I opened her garage openers control hood to reprogram her remote (wallah)👏. Now no other remote works with her door.

[celinenguyen]

I want to set up a second Marantec garage remote opener, but the first remote is broken. Is there a way to fix this?