✅Best Garage Door Bottom Seal | Rubber Gasket Weather Strip Replacement DIY HD Review

[SzechuanChickenDog]

Love the lunch lady kitchen gloves....😅😅😅😅
Great video. I subscribed

[eaunver]

You should increase down travel of the door another 1/2". It will seal the gap better.

[stewsmith]

Super great how to video. Now I just got to get my helped involved like you did! The Amazon rubber gasket looks like the right way to go. Thank you!

[hectorg.]

Most garage door weather strips are made with a very thin and cheap rubber (unless you want to spend $200), the one you used is built so much better than the average and at a great price. Thanks for posting the link for it.

[Theshootfashion]

Thanks for the great video. Much appreciated!

[blackericdenice]

I bought my first house 4 years ago last month. The garage door broke the first day. I watched a few youtube videos and was able to fix it. My neighbor said he paid a company $4, 000 to fix his. Thank you for you video. I've been wondering why my door don't go all the way down.

[trtech]

Great video! Super thorough and informative. Saves me so much money instead of hiring someone to do the job

[Alycanj]

I have one bent to hell track and no idea what size should go in and had to cut and scrap out old seal, what a pain.

[cindyrsdu]

Can you please answer my question? We have an 2 garage door similar to yours, except our garage door when down sits on the concrete, not the garage door. Our takes the U shape rubber. When we put the new rubber on we are seeing light from second panel and little light on third panel. The old rubber u shape didn’t show light and the reason we took that off it had broken on the right side. Do you have any ideas of what we can do concerning light coming through? Cindy

[davidmohr]

If the seal is in good shape, but doesn't seal well, I use foam backer rod inside, 3/4", 2 lengths, pulled into seal interior with an electrical fish tape. Works pretty well, until complete replacement is necessary. I'll be using the seal used in this video when the time comes.

[benhuang]

I want to replace my seal, but I am still wondering whether the thickness of the T-slot should be 2mm or 1.5mm. It is said that 2mm will be difficult to install.

[KJC]

you should have a hole on the side of your garage door opener motor casing, turning one way will make the door come down further - so no light gets in.

[privatename]

You guys are lucky if you have this type of garage door track. The one I have has metal plates on the outer edge blocking the ends of the T-channel, so I can simply slide it off. I guess I need to remove the entire channel track but without moving the lower hinge plates of the door (which are bolted over it) because those plates are also attached to the pins for the high tension wires attached to the torsion spring.

[HereWeGoo]

This was brutal. When your seals won’t slide in the T-track, good luck.

[mykalimba]

I have a similar situation on my garage door, where the original seal is about 4-6 inches shorter than the door on each side, and I'm pretty sure that the seal spanned the entire door when it was new. Where does all of that length disappear to? Some alternate universe? 🤔

[BF]

How do you know what size to get 1/4" or 5/16", where to you measure to make sure? Thanks

[adgar]

Thank you so much!! This video helped a lot and my wife was pullin it too just like yours lol one question, I bought the exact same reinfirced one as you but now my garage door wont close all the way, do I have to tweek the chain or regretably go with the cheaper thinner rubber?? What do you recommend?

[prxjectcris]

I been installing mines but its really hard to run it. I cant pull it, i also applied silicone lube but no shot.

I can only feed a quater of it

[jamesplatanitis]

what about mice getting in lots of room for them to come into your hotel ; ]

[GhulamAli-jhun]

The garage door should rest on the recess to completely seal not on the garage floor as the video shows.