Syil x4 new drive pulley and new motor bearings

preview_player
Показать описание
I noticed a noise coming from the quill on my Syil x4. Turned out to be a dodgy bearing on the motor.
So in this episode we replace one of the drive pulleys and fit new bearings to the drive motor.
This made a significant difference in vibration and hence the surface finish on machined parts.
  1. Cazual Haze
  2. Syil
  3. syil x4
  4. cnc repairs
  5. cnc maintenance
  6. diy cnc
Рекомендации по теме
Syil x4 new 0:20:02

Syil x4 new drive pulley and new motor bearings

Syil X4 Spindle 0:04:24

Syil X4 Spindle and Controller Upgrade Part 1

Syil X4 0:00:12

Syil X4

Rebuilding a Syil 0:03:07

Rebuilding a Syil X4 CNC Mill - Introduction

Syil X4 4th 0:02:16

Syil X4 4th Axis Gear Cutting

Würfel im Würfel 0:01:44

Würfel im Würfel auf Syil x4 CNC

Montageteile auf Syil 0:01:54

Montageteile auf Syil X4 gefräst

New Project: Syil 0:06:03

New Project: Syil X4 CNC Mill Control Conversion Sneak Peek.

SYIL X4 CNC 0:38:13

SYIL X4 CNC Mill, Teknic Clearpath SDSK, Centroid Acorn Project: Brake and Z Axis Tune

SYIL 7 CNC 0:00:51

SYIL 7 CNC Machine. Delivery day episodes 1

Syil X3 upgraded 0:00:41

Syil X3 upgraded to servo motors making a few simple cuts

Kreistaschen in Plexi 0:02:27

Kreistaschen in Plexi Fräsen auf Syil X4 CNC

Syil X5 CNC 0:01:34

Syil X5 CNC Vertical Milling Machine

Neujahresgruss 2016 cnc 0:01:58

Neujahresgruss 2016 cnc graviert mit syil x4

Alu mit Hf 0:02:13

Alu mit Hf Spindel Fräsen auf syil x4 cnc

Satisfying SYIL CNC 0:00:08

Satisfying SYIL CNC Milling | SYIL Shorts

SYIL X4 CNC 0:50:13

SYIL X4 CNC Mill: Teknic Clearpath SDSK Centroid Acorn Project: Overview and Unboxing

PM727M Belt Drive 0:22:54

PM727M Belt Drive Bearing Block

What's it like 0:31:12

What's it like after 10 years?

SYIL X4 CNC 0:34:31

SYIL X4 CNC Mill, Teknic Clearpath SDSK, Centroid Acorn Project: Back Panel In Cabinet & Setup

SYIL X4 CNC 0:07:56

SYIL X4 CNC Mill, Teknic Clearpath SDSK, Centroid Acorn Project: Basic Panel Layout

Emco PC5 to 0:15:53

Emco PC5 to Centroid Acorn Conversion. Part 4: Spindle Motor Fit Up & Wiring

Work and tool 0:05:29

Work and tool offsets on the Syil X7 LNC6800

Teknic Motor Driven 0:00:21

Teknic Motor Driven

Комментарии
Автор

Hi long shot I have the same syil x4 plus, my laptop died that run it and I had no backups.

Would you be able to email me the mach 3 xml profile please.

Or even share your mach 3 setup please.

I've hunted everywere and syil support is shocking bad.

AcidVFRR
Автор

When spinning the milling shaft to show hall sensor those bearings did not sound too healthy.

incubatork
Автор

Hate to say but there is something else that is going horribly wrong in this whole assembly. Spindle itself, the whole motor is faulty, or something else. I have the exact same Syil X4 Plus with an identical motor and no where it sounds like yours. Quite smooth, even freq, zero vibrations and reasonably quiet all together rather.

gtcollection
Автор

Hi do these come with a power draw bar or was that something you had to add later on? Also is it possible to make a tool change post and code some tool changing procedures? Im looking at buying a new Syil x4 as my first machine and just wanted to get some advice from an advanced user before pulling the trigger and killing my wallet. Thanks

DaveNorthWest