Wet Cell VS Dry Cell. Hydrogen Generator HHO. Fuel from Water

Hello. First of all, thank you all for your support and thanks to you I have come this far. Thanks for the messages and likes.
In this video I do exactly what I promised you, the dry cell hydrogen generator versus the wet cell hydrogen generator. I will test the production of hho with a new instrument for measuring liters per Minute (l / min), And I will measure the amps consumed.
We made an identical electrolyte mixture for the two hydrogen generators to make the exact difference between them. For the electrolysis of water I used distilled water and potassium hydroxide and as an electricity I used a 12V battery. The generators Know them from the past videos, were presented step by step how they were built. They consist of 9 316L stainless steel plates with a thickness of 1 mm and a diameter of 60 mm.
I was surprised to see that the dry cell produces 1 L / min (one liter per minute). I was surprised because it is a very small cell with only two elements connected to electricity at positive and 1 at negative. I got a nice electrolysis so to speak.
I think this putty can be easily used for a small scooter, a small motorcycle or a small motor bike.
With these small generators we can get free hydrogen from solar panels that produce solar energy. Free energy, free electricity. Hydrogen free, Fuel free.
Thank you very much for viewing, give a comment and a like please and follow me to see a new special hydrogen generator that is made with the remaining materials from other generators.

[Inventive]

Friends, let's promote this channel to see what other surprises it brings us. Like comment and share please

[mikewalsh]

Keep in mind the flow meter is for oxygen only and calibrated only to that. Since HHO gas Is two parts hydrogen that will throw off the meter, usually showing more LPM than you actually have. I found this out back in 2007 doing similar experiments.

[raghuveerdendukuri]

really nice, good experiment, happy to see dry cell is always outperforming wet cell.

[thefeet]

I've been watching the HHO community for a long time. You earned my sub. I have long suspected dry-cell was the way to go. This confirmed that for me. To the guys who say you never hooked up the wet cell long enough? come on...do you REALLY think that wet cell would catch up and out-perform the dry cell in this experiment? Like... electrolysis is some sort of "marathon" where the wet cell catches up and takes over... wins and arms flailing across the finish line??? pffft... wet cell is a MESS to deal with to begin with...

[Prodigal]

Very well done, the music got a bit annoying toward the end but that doesn't take away from a very high quality HHO wet / dry duel.

[JDekca]

Those were put together very nicely. Thanks for taking the time.

[qqqqwwan]

Awesome brother. Your Kit quality and its precision is absolutely amazing. really very impress.

[TravisTellsTruths]

I'm glad to see its not THAT different! 👍 Great test!!

[doutorhidrogenio]

Definitive prof of dry cell eficiency., Great man, thank you for excelente work.

[SurpriseToysShop]

May I know how many watts, amps, volts were in the LPM test in the Dry and Wet Cell? LPM test looks like with over 30A 360Watts 12 Volts? Why is the ball wet inside the LPM meter in the Dry Cell test? If you leave the LPM meter wet inside, you may get inaccurate 5 LPM results. Can you do a real test with the bottle?

[hhogasproduction]

Thanks.Sir
Good information about both cell.👍👌👌👍 nice Sir your job 👍

[RodneyEgonio]

Hello sir! I just imagined if you could try the hard drive platters (from defective HDDs) as HHO plates instead? A video for this would be very much appreciated. Thank you!

[iwankurniawan]

Semoga sukses untuk semua karya yg anda kerjakan 😊

[waynesanders]

Nice to see you give the dry cell a full minute of run time to warm up from 1/2 LPM to almost 1LPM, but the wet cell gets about 8 seconds of operation starting at 3/4LPM. The wet cell produces more gas when the results aren't tampered with, and that dry cell setup you have isn't like other drycells that are actually implemented which usually only have 1 hole for gas to escape with worse flow characteristics, and need disassembled and cleaned every few months because the electrolyte cakes up inside of the plates because of high amps, low volts, and bad flow. Although you have the terminals situated similar on both the dry and wet cell, because you have them right next to each other it makes the wet cell less effective at producing gas because they're 30 degrees from each other vs 180 so the electrons can't jump right from the positive to the negative. That has no impact at all on a dry cell. You also put so much water in the wet cell you couldn't let it run more than 7 seconds at a time because it was beginning to produce so much gas, but because the ratio of water to metal was too high the bubbles couldn't pop (because you used the usual amount of electrolyte needed to run a dry cell, less is better on a wet cell) . A properly designed wet cell will blast that dry cell out of the water if done correctly, and it brings along with it water vapor which cools the combustion to reduce NOx emissions. Making it similar to a dry cell then using it as a wet cell makes your video give skewed results, much like is usual in media today. I've been doing this 9 years myself and will be starting my own business next year installing on large diesel trucks. Anyone can buy a kit on Ebay or Amazon these days and point a camera at it. Knowing what you're doing when designing a system is something completely different. I'll throw you a bone almost no one has figured out. Neutrals are a waste. There is a way to make a full voltage cell that won't rust and run at 7x the capacity (per amperage) of a dry cell system with just that one change alone. And there are several other things that can be done with a wet cell to add more output that can't be done with a dry cell. Heat can become your friend in a wet cell. In a dry cell it will start filling the plates up with soap particles.

[kwasiadu-amankwah]

How long will the stainless steel electrodes last

[TVmadethemdoit]

Do make the plates yourself, or do you purchase pre-cut patterns from somewhere? Thanks

[therealtpain]

You left the dry cell hooked up WAYYY longer until the ball rose to 1, then unhooked it. The wet cell you didnt leave hooked up long at all compared to the dry cell and i feel like if the wet cell stayed hooked up it would end up at 1 as well

[vick]

Nice, where you got the measure device? Anyway great results on 6 amp.on drycell.

[veerababunukapangu]

Nice thinking, Fitting box material you use for dry cell and wet cell water storage, Acrylic or poly-carbonate clear sheet ? and how much thickness?

[ngmngoc]

Really nice 👍, can i have a question boss! What kind of power you using boss? Thank you boss .