Inboard Propeller Install and Removal | How to use an Acme Prop Puller

preview_player
Показать описание
We are going to show you how to remove your Propeller and install a new one. Here are a few tips and tricks that make this process a breeze.

*Use a block of wood to keep the prop still
*Use a Prop Puller to make the removal a breeze

As always you can call us for any help at 803-345-0996.
  1. SKIDIM
  2. inboard propellers
  3. boat propeller removal
  4. removing a inboard boat prop
  5. inboard prop install
  6. removing inboard prop
Рекомендации по теме
Inboard Propeller Install 0:05:26

Inboard Propeller Install and Removal | How to use an Acme Prop Puller

Inboard Prop Removal 0:00:53

Inboard Prop Removal (www.skidim.com)

How to install 0:03:21

How to install an inboard propeller by propshopinc.com

How To Remove 0:11:19

How To Remove An Inboard Propeller

How To Remove 0:01:46

How To Remove An Inboard Propeller

How To Remove 0:11:44

How To Remove An Inboard Propeller // Malibu WakeSetter LSV25

Pulling the Props 0:06:01

Pulling the Props on an Inboard Boat

How To Replace 0:03:11

How To Replace a Boat Propeller | BoatUS

Installing A Ski 0:04:46

Installing A Ski Boat Prop

How to Change 0:09:58

How to Change a Boat Prop

Propshaft Coupling Removal 0:12:07

Propshaft Coupling Removal Direct and Drive V-drive

Boat Inboard Propeller 0:08:00

Boat Inboard Propeller Installation Tips

Shaft Alignment Part 0:08:52

Shaft Alignment Part 2

How To Install 0:03:06

How To Install A Mercury Flo Torq II Hub Kit

How to Remove 0:06:25

How to Remove a Marine Driveshaft/Propshaft Coupler For Inboard Direct Drive Boats

How to Install 0:01:35

How to Install a Mercruiser Flo Torq Propeller

How To Install 0:04:14

How To Install A Hub Kit

Repacking a Packing 0:05:26

Repacking a Packing Gland/Stuffing box with a Rope Seal on an Inboard Boat

How to install 0:06:13

How to install a Quicksilver / Mercury Flo Torq II or Michigan Wheel XHS Hub Kit

How to Install 0:20:42

How to Install an Electric Sailboat Motor - Catalina 30 - Thunderstruck Motors Sailboat Kit

How to replace 0:14:10

How to replace an impeller on a Mercury inboard

How to replace 0:06:44

How to replace a typical Ski Boat Strut Bearing (aka Cutlass Bearing)

S4EP2//Installing an Inboard 0:20:36

S4EP2//Installing an Inboard Diesel Engine W/Folding Prop From Scratch

Outboard vs Sterndrive 0:11:44

Outboard vs Sterndrive [ Inboard Outboard vs outboard ] Which is Best? why? Inboard vs outboard

Комментарии
Автор

Great video! Agree on the cotter pin comment, new stainless one every time!

bjlee
Автор

What a great idea for a channel thanks for sharing your page with me I’ll see if I can’t get it out there for you some and vice versa thanks
Dale

DaleWHickman
Автор

What a great idea for a channel thanks for sharing your page with me I’ll see if I can’t get it out there for you some and vice versa thanks
Dale

DaleWHickman
Автор

Do you have a video on replacing a broken prop shaft strut? we have 1981 WellCraft 248 sportsman with a velvet drive, the shaft strut is broken just below the hull mount.

ginsudan
Автор

I’m always glad to see another video from you. Question- should you or could you use anti seize on the propshaft? I’m in freshwater 100%.

daveaustin
Автор

I'm working on a Malibu right now 350 block. After about 30 mins of use, it's losing power after about 30 mph. Just cuts out. If I pull back on the throttle, it will run alright. But if I try to go faster it just kind of cuts out. I have run through the basics, connections, filters, etc... Advice?

DetroitWrecker