How to Replace the Front Wheel Bearings on a 2009/2010 Honda Odyssey

Website

Stay connected at:

Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick. #howtoautomotive

[oldschoolteacher]

Thanks Brian. You’re a top notch teacher to us diy mechanics!

[DH-rtwl]

Thanks for the detailed video, you've successfully convinced me to just pay a professional mechanic to do this...I can forsee many points of possible problems and requirements for specialized equipment

[yahu]

Very precise and in detail, excellent instructional video

[SteveRobReviews]

Well done buddy. Wow over 200 ft lbs on the Honda . My 2500 HD is around 170 . And the bearing was hammered on for 20 minutes just to break the rust. LOL

[Eagle_fire]

Great explanation, I'm about work in my tomorrow.... thanks you so much....👍

[NBFILMS]

i have a 2004 Acura mdx and it's the same set up as this. thanks for the video!

[ashuye]

You are the best !!! Very detailed explanation ....am sold out. O wosh you are in Houston so that i will bring my Honda Odyssey to you. How much will cost me for both front bearing to change...aproximetly...

[sombongi]

Nice illustration, even for a seasoned mechanic like me I learned a thing or two that I do differently.

[timfarrell]

Top notch video! Thanks for all the great info!

[zubairsahi]

very nice video in detail l have a question after replacing the bearing if there is any risk of suddenly ABS on 120km

[ojarquin]

Awesome video, thank you I got to do shafts on 06 Oddy, Best video I've seen

[violaboy]

thank you awesome video.... subscribed

[ducadae]

I'm about to do this repair to my 2009 accord. I'm assuming the procedure is identical. Is this correct?

[realityconformist]

When you removed the snap ring, you removed a "seal" or whatever you called it and "set it aside" Did you put this "seal" back over the new bearing before you reinstalled the snap ring? Or, was that part of the old bearing and you threw it away? Some videos don't mention this "seal". I saw another video and they called dit a "backing plate". I can't find this "seal/backing plate" anywhere on the honda diagram. Some videos don't even show removing it. Other videos like yours, show removing it and setting it aside and then just skip over reinstalling it, if they installed it at all and go right to the snap ring

[hcauq]

Great video - I just wanted to replace broken bolts.  Can I just remove the hub only?  I don't need to replace the bearing.  Is there any tools I can use just to remove the hub?  I am thinking of grinding down the bolts to fit them in.  Thanks

[USMC-ceek]

Great video, would this be similar to a 2005 Honda Pilot AWD? Thanks

[zaro]

I love that my 2014 odyssey has wheel bearing hub assembly. Sure it cost about $110 with shipping, but you can get the job done in about 1hour with no special tools, apart for a breaker bar and the 36mm socket for the axle nut.

[cdurkinz]

Having a hard time with the "Wheel speed sensor" (which I believe might be the ABS sensor), any tips? Thanks!

[rev]

I was unable to get the control arm and ball joint loose. I was using a small hammer. Could that be a problem? Any tips on how to get them loose?

[tazlama]

Hello been following for a while now and need to replace wheel bearing...having the most difficult time removing axle nut...i am using 1/2 drive 24 inch breaker bar and have a cheater bar about 3 feet and still wont come off..am i doing something wrong here..someone said there is a pin that needs to be flattened out and broke a tip of my screw driver in there...could that be it, ...am so lost, i know that its tourqued in there good but wow, breaker bar with a cheater bar have never had any problems before. Please help, thank you in advance