Modular 3 in 1 3D printers Creality CP 01 vs Snapmaker 2

Please share the link above with your social group, I really need all the help I can get, and good will. Thank you.

This video discusses the modular 3 in 1 3d printers snapmaker and creality cp-01. Creality cp-01 is launching the cp-01 modular 3 in 1 3d printer and it is a new comer in the 3 in 1 3d printer market. We are doing a comparison in between the snapmaker 2 vs creality cp-01. The CP-)! seems like a good Snapmaker 2 Alternative.

*************************************************************************************************
Amazon Affiliate Links Below: As an Amazon Associate I earn from qualifying purchases
*************************************************************************************************
I found that my iFixit ToolKit 112 bits helps me with 3D printers very well. In addition I have used it in building furniture and tinkering with the car
*************************************************************************************************

[juddhaiss]

Will be boxing up and returning my CP-01 tomorrow. Runs very quietly, when you can get it to run. Wouldn't read SD cards, except the one that came with it.Bought an external card reader for my Mac and 3 new SD cards. Each card worked 1 time, then would no longer work. Tried quick formatting, overwrite formatting, still no luck. Software included is for windows, so I downloaded Mac software off Creality's website, which wouldn't open. Milling head was missing the screws that hold the motor in, so motor was rolling around, which damaged the circuit board. Had a big green OK sticker on it, like it had been quality checked, though. Bed was very high in the middle, which could probably be fixed if I was going to keep it. The touch screen was very nice, as well as the ability to micro-adjust the z axis while the first layer was going down. But I'd like to be able to print more than the rabbit, pikachou, and flexi-cat files that it comes with.

[Ben-mtyj]

The Creality is on AliExpress right now for $567

[snowye]

I just got the CP-01 and have no major issues with it at all. Extrememly quiet and give good quality prints and laser engraving is really easy to use, haven't tried the CNC head yet but have turned it on and find no problems with it. Took me 20min to install but it's kinda a pain to level the bed, the center is slightly higher than the edges and the bed is slightly wobbly which after reinstalling the wheels reduced it. I use Octoprint so have never really used any alternate SD cards. Still the only complain I have would be for them to have ABL added, because it's kinda stupid that you have to take 10min leveling the bed after you change the tool head.

[mujo]

he made it to the end before pissing himself lol 😂 love it. Haha I wish my snow maker was a snap maker 😬

[TheChainsawKid]

What nozzle does the CP-01 use? I know that they're not all the same and want to know what nozzle design it uses before purchasing the wrong ones.

[johnstewart]

Hey...me again. OK, my heat head failed....thermistor shorted against platform clip? Creality says I can use the Gcode files to test the laser and CNC heads. WRONG!! I select the laser head, raise to 100mm, focus (move the work piece to be under the spot, near the edge of the table.) The instructions then say to select “ procedure selection, ” but that DOES NOT APPEAR. Select the “gou” Gcode, and it reverts to 3-D printer mode! SO FAR NOTHING WORKS! $630 anchor. I am trying to work with Creality, but they apparently are “out of office.” I got the auto-reply.

[genin]

Cool channel but any chance you guys can use a different robot voice for the voice overs? Maybe somethings softer

[johnstewart]

$625....work platform not attached (5hours to install)...instructions booklet very incomplete....thermistor bad, not heating nozzle, no printing....no software included, only 3 models on SD..I would NOT recommend this, not ready for prime time.

[giulio]

what about the spindle power? can you give us the watts of them?

[kacper_]

You cant really compare these two the snapmaker is twice the price

[labestialceramica]

Hello. I have a question about any of these two. Are they more like a hobbie machine? Like to start, or are they machines to work with quality and reliability. Im about to buy 3 d printer, so i guess this multi function machines are not so good as one fully designed for one task. Can anyone give me some lights about this. Thanks