How to Flash BLHeli with ANY Arduino! | Create ESC Linker, 1wire interface

You don't need a special ESC programmer or flashing tool to flash BLHeli; just grab any cheap Arduino and two wires and you're good to go! In this tutorial, I use an Arduino Mega 2560 to flash a cheap, generic ESC with BLHeli.

-----------------------------------------------------------------------------------------------------------

-----------------------------------------------------------------------------------------------------------

#esc #blheli #diy

[Kaizer-qekk]

Very well explained.... You just got another subscriber.

[tuando]

Very well explained tutorial! Short and easy to understand for a newbie! Thanks for your time :-)

[logiloigloig]

Hi, I am using an arduino uno and the HobbyKing® ™ Brushless Car ESC 10A w/ Reverse ESC. I have followed your tutorial, but it doesn't seem to work. What can I do? (The problem is that it doesn't detect the esc). Thanks!

[ahalgamal]

thanks for the video, i have a ZMR blheli 50A ESC and got stuck in the bidirectional mode, which disabled the programming mode, i followed the video but the ESC is not recognized by the BLHeliSuite nor BLHeliSuite32 .. how can i exit this bidirectional mode and make it forward ?

[lukaspfitscher]

Can i test the motor directly in blheli didnt finde an option? Great video 😉

[leonardfpv]

Can you please advise how to find the suitable firmware for the no name ESC

Thank you so much

[Timetravel]

Do you have an scematic for wiring my Pixhawk4 with an Arduino uno or an Arduino Mega 2560

[vtolrakesh]

Hello Colton,
I want to flash the firmware to the DYS 30A ESC, for this they have used Simon K firmware but I didn't found in target ESC option in BL Heli suite 16, how can I flash the firmware to DYS 30A ESC

[gerykis]

Is there any way to control the motor with arduino interface ? I have just the motor + blheli_s 30A + arduino . I can flash but I don't know how to test the motor .

[keshavharipersad]

hey nice tutorial, just one question .. i have a blheli_s 4 esc board and i want to flash / use it with arduino nano .. how can i do that .. ? the blheli_s board has 4 signal pins btw, just like the normal single esc, so i thought maybe do it like that? help pls

[adrienfaure]

there is no arduino due in the board selection in blhelisuite . did i do something wrong or the firmware doesn't support this board?

[DanielCruz-vpmg]

Hi, i have an unbranded esc with green pcb and two chips, one is fortior fd6288t and the other chip does not have any labels. Help me identify what esc is this please D:

[Timetravel]

Do you know if it is possible to read out an bricked PX4

[Timetravel]

I dont know wich blheli firmware I have to flash on my SIMONK 30a .
My type does not show on the flipdown page .

[bhamkertima]

cant get selection on the firmware.. its empty. how to solve that?

[Timetravel]

😂😂😂 ok no problem.But if you want a challenge try and unbrick a PX4 .If you succeed you would be a hero to all PX4 users😁😁

[naveedmazhar]

Hello
I am using YEP 40A ESC with Arduino Mega 2560 (PIN D51) and I get the following error.

Serial Interface “m4wFCIntf” connected successfully.
Connection to ESC#1 failed!
Please check data- und power-connections to ESC!

Kindly help in this regard.

[crouserhd]

and an Arduino Uno. If i do everything like you did in the Video, I can connect the Arduino with BL-Heli, but after I press "read Setup" the Programm says "Please connect the ESC and power up".
After 15 Seconds there is an error message.

I don't understand why this Messages Comes, because i connected everything like you told (GND -> GND / Data -> Digital Pin 2)

Could you help me?

[wibbyarief]

Hello. Can i use Arduino Uno for this purpose? Or maybe Nano?

[Stodgyaban_]

Hey i can’t catch up what are you saying. Put a subtitle please 🥲