How To Adjust The Needle in Your Motorcycle or ATV Carburetor

Click here to subscribe to our channel!

[micahjared]

From deeep in the Mts of NY > Thank You. Ive gleaned a bunch.

[mikehatherall]

Thanks for the time putting this video together. it educated me some.

[JoshHopkinsYT]

Thank you for the really helpful and to the point video

[ហេងមុនិន្ទ]

Can I use 2003 yz450f fcr carburetor rebuild kit for 2003 wr450f fcr carburetor? Is it fit?

[Stevie_b]

Question I have a yz426f and in mid throttle it sputters. It this caused by to rich or do I gotta move a clip to lean it?

[Merc]

why didnt you cover which clip position is #1 and which is #4 etc. are we going from bottom or top??

[crazedmoto]

I have a flat cr like this and I have that electric solenoid that's like a main jet shut off or something and I think it quite do you have any videos on that don't want to pull it out till I know what I'm doing it's got those tamper-proof Torx keys and I wanna know what I'm getting into before I pull it off it's just a swap a new one and let me know because I think it quit whenever I rev the bike without the choke on it just dies out clean carburetor everything else works good Jets and you don't write everything worked great till I think the solenoid just quit.

[bg]

Great video. Would using 2 year old oil/fuel mix contribute to fouling plugs? I have a 1999 Husky WR125 and it was fouling plugs all day today. It was over 90 degrees with high humidity and the fuel was old.  I was thinking of adjusting the needle, cleaning the air filter and replacing the fuel.

[kareemvitar]

Thanks for the video.but how do i know that my carb is adjusted well?

[MrLawnmowerman]

Can you do a video on installing a dynojet jet kit to a 400ex or similar quad please?

[TheMisteraska]

Man if i have a big stutter between 8 and 9k rpm on a 13k redline engine, what should i try? I tried the main jets and a good carb cleanup and refurbish but the problem is still there

[brendanpike]

I have a kx250 four stroke 2007 were do I put the Needle

[Hondatrax]

My atv bogs a little when around 1/4 throttle, but has lots of power from1/2 throttle to full throttle and should i do this?

[rmatvmc]

Did you receive the pdf installation instructions with your Dynojet kit?

[elimartinez]

Ok so i have a four wheeler and the carburetor needle is not pulling up or down. At this point i think its my throttle. What do u think is wrong with it? Any suggestion will help

[notsotacticalninja]

How can i now how high to put needle clip if i dont have any service manual?

[chumbrega]

I am using 50:1 on trails. my spark plugs are getting ruined all the time. They told me to move the pin on the needle so less oil gets to the top end. I dont know if I move the clip down or up. Thank you.

[chriscrezz]

My 2005 YZ450F is backfiring. it idles fine, so the pilot jet is correct. But once i open the throttle and let it off the backfiring starts. Should i move the needle richer or leaner?. Thanks in advance. 😊

[Garethuk]

Does this work in combination with the fuel screw on a 4 stroke? I keep fouling plugs making it impossible to start so i moved the clip one step to lean. I revisted the fuel screw today and it's currently 3 turns out but it seams to prefer 4 but it wont idle. I'm assuming if i move the clip again i won't need the fuel screw out so far? Yz426

[nicksalter]

I have a 2003 rm125 is it same way removing the needle I'm having a hard time.