MKS sBase unboxing & preparing to install

MKS sBase unboxing & preparing to install

Overview
SBASE is a latest motherboard for 3D Printer ,designed by Makserbase (MKS).
It is based on ARM platform and uses 32bit 100M Cortex-MS MCU-LPC1768.

MKS SBASEV1.3
1.Fix temperature problem.
2.Add thermocouple Pins( can't be used with 12864lcd together).
3.Create some pins P1.22 P1.23 P2.12 P2.11 P4.28 for developing.
4.Extend endstop power 3.3V / 5V.
5.Preassemble two big heatsinks.

Features
1. Using 32bit 100M Cortex-M3 MCU-LPC 1768, and improve its performance highly.
2.Support highly modular open source firmware Smoothieware, easy for secondary development.
3. Support network function, then proceed remote control via IE Explorer.
4. Using DRV8825 stepper driver which supports 32-microstep and with excellent cooling.
5. Currents of the stepper motor can be set directly, which can avoid the damage .
6. Using high quality FR-4 4 layers PCB and special design for cooling.
7. Using professional power chip, support 12V-24V DC input.
8. Good to work with 12864LCD and MKS TFT touch screen.

MKS TMC2100 V1.3 Stepper Motor Driver

[TheCyberling]

some explanation of what you were doing would have been nice.

[lashawnrobinson]

Hi, I am currently setting up an MKS Gen V1.4 on an Anet A8. I have a cable that split my dual Z from one DRV8825. Around 10:50 of your video, you jumped connections. Is this considered as a parallel or split? Would you recommend one method over the other? Thx!

[mirceapuscasu]

I use a configuration from SgaboLab smoothiware, end stop BIQU Equipment Endstop Mechanical Switch without Pulley Wheel. I can not handle these settings especially in arduino so I wanted to help me with the configuration you did, my 3D printer is the old model of the BFB 3000 that does not work for a year

[gsidTV]

please dont dril directly with the board. mark with a pencil before drilling. you may accidentally damage traces on the board. considering its a 4 layer pcb, you wont be able to repair with straps

[mirceapuscasu]

Hii mate I have same board making start with 32" tft display ready installed firmware display working but no answer , I speak with Kingprint and have received details about need connect termocuple, please help me with this problem ifs possible. Thank you

[antorlun]

Hi, i have a mks Robin 2.3 board but cant change config to Corexy and cant enable extrusor 1, can you help me?

[mirceapuscasu]

Like idea on my configuration nathing else, wath I don't find, any explanation about termocuple and I will be very happy with your help if possible please. Thank you

[machwasmakerspace]

It's kind of funny... to see you drilling trough the gaps of the electronic priints made me think: Ohhh no, don't do so, thats bs....
While I have to say, that I'm not doing better sometimes... ;-)

[mirceapuscasu]

If i want to connect the end stop with 2 wires i have to connect it to the plus and the signal, if i connect it to the minus and the signal does nothing

[mirceapuscasu]

Hi, I have a stop ending problem when I get home close all the system can not reopen it unless I manually mutate, how can I fix this problem, I tried with the two types of end limit and the same problem, is it something from the configuration? Please help me

[mirceapuscasu]

It's a possibility to help me with the configuration you use, please

[mirceapuscasu]

Excuse me, I connect plus with minus and so stops I'm putting them in short circuit :(

[Golkun]

Without any comment what you are doing, this video is useless.