setting z-offset on anycubic kobra neo

setting z- offset on anycubic kobra neo

[BATRC]

I love this video! I deal with ptsd and anxiety, which makes me forget everything 🤷🏽‍♂️. I have come back here probably 15-20 times for reference. Thanks!

[CPurdiePlays]

This has saved my sanity, my printer, and my job haha. I've found other videos out there but this one helped me the most. Thank you so much!

[jdibagg]

this video is the best, its short, gives you exact steps and best of all it sets your z offset! thank you .

[xChazzar]

Sir, i applaud and thank you very much for this gem of a video. i bought myself this exact unit and ive done many prints but never been happy with the initial layer. i also found that prints were coming unstuck from the base and even bought some adhesive which worked but still unhappy with bottom layer. since following your video i have now prints with a flawless foot.

[anthonydowling]

Thank-you for your guide. I am having real bad issues with the PLA adhering to the bed. Your guide makes the most sense out of all of them & I have recommended people look for your vid in my Amazon review

[JohnDoesDrones]

Holy shit THANK YOU. I've spent the last hour messing with the z offset thinking I was doing it too much and it wasn't working, only to find out I needed to crank it a lot more. Working now.

[redi]

this is exactly what I was searching for. i have the kobra 2 but I'm pretty sure it's the same steps. So I assume you generally want to first run auto level, which will measure across the bed and build a map. then you home the print head, set the z axis height to zero, turn the motors off, move it in the middle and use the paper. pretty easy and way better than running test prints and randomly adjusting z offset.

[hanshase]

Hello, thanks for the video, it helped me a lot. I've had a Kobra Neo for 3 days and I'm almost desperate about leveling the nozel. is never really shown where. after your video it finally worked. thanks for the video.
Many greetings from Germany

[tonyk]

put a feather in your hat son you are a genius.... strict and to the point with no BS Fantastic work.

[TheSolo]

going to give this a go thanks for posting was on it for over 6 hours yesterday used the filament that came with it and some of a spool i bought gave up at 6am works ok just won't stick to the bed gets about 8 layers up on the bottom of the owel when the nozzle touches it slightly its moves it from the heat plate
😂

[hermestri]

great video, you should do more tutorials, very easy and right to the point, i hate videos that are like 15 minutes to explain a process that only needs 3 minutes to explain, thanks, a video explaining how tight the belts and the Z axis wheels should be would be much appreciated if you ever have the time to do it

[Hiaki]

I love you for this video fr step by step quick guide, amazing!

[RwP]

Near this topic, wondering if you see the same thing. I got the Kobra Go with ABL. It sucks out of the box, the bed level deviation is 2-3 mm across the board, and the ABL doesn't compensate for this enough, one side will be smashing the filament and the opposite gapping. I can see the Z-axis moving, so it's running the mesh during prints, but not good enough. I got the yellow bed springs installed where the stock bed standoffs were, then did a manual bed level with the PEI spring sheet (it's not flat either, so got to measure with that sheet on), and after getting the bed flat manually, I run the ABL and see the mesh map is much better within 0.3 mm of each other. Still I'll run ABL to compensate for the middle. I did a full bed flatness test print and it is perfection everywhere I'm really impressed.

[arathoonfamily]

thank you sooo much I was trying to work it out for hours until i saw yo video really thank you
❤❤❤

[xjrdrz]

When i did the same 2 months ago it damdaged my bed with nozle becasue zero on z-axis in idling state is different from when it's printing. In idle it's higher and when i set offset and started printing it tried to go under bed. It might be just a malfunction in my case but better adjust it like it's shown in instruction - while printing. Luckily magnetic cover is double sided. That time i also set something about -4 or -5mm offset, now it's running on -1.18

[glennthefrog]

Thank you this is the most simple and useful information

[snapap]

Great video. But have a question. When I go back to z offset I still get a reading of 0.000. When I start the print I have to manually adjust it to the bed so it sticks. Why is this

[Slash_a]

Thank you so much for making this video, it helped me out a ton!

[grigorigrigoriev]

Thanks a lot, that's what I've been looking for

[NagaEvolution]

Please make more video on the neo❤️❤️❤️