WHICH SIDE IS BANK 1 AND BANK 2 TOYOTA SIENNA 3.5 v6 engine

WHICH SIDE IS BANK 1 AND BANK 2 TOYOTA SIENNA 3.5 v6 engine

This might be helpful for the whole generation from 2011 to 2017:
2011 Toyota Sienna Which Side is Bank 1 and Which Side is Bank 2
2012 Toyota Sienna Which Side is Bank 1 and Which Side is Bank 2
2013 Toyota Sienna Which Side is Bank 1 and Which Side is Bank 2
2014 Toyota Sienna Which Side is Bank 1 and Which Side is Bank 2
2015 Toyota Sienna Which Side is Bank 1 and Which Side is Bank 2
2016 Toyota Sienna Which Side is Bank 1 and Which Side is Bank 2
2017 Toyota Sienna Which Side is Bank 1 and Which Side is Bank 2

Our Most Popular Videos:

♦♦♦ Cameras & Gear Used For This Video ♦♦♦

•Cameras

•Tripod

•Microphone

•Light

•Comuter for editting

♦♦♦ Other Equipment and Gear that I use ♦♦♦

•Camera

•Extra Computer For Editting

► LIKE & SUBSCRIBE for MORE DIY VIDEOS that could SAVE YOU BIG $$$$$$$ !!!

This is not a sponsored video. Everything is purchased by us!

The video is meant for entertainment purposes only. Do not Attempt!

AMAZON ASSOCIATES DISCLOSURE

*Disclaimer
We, Auto Repair Guys, are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not Auto Repair Guys.

[AutoRepairGuys]

⛐ Check out our Garage to see what tools we use and recommend:

[yrot]

it should be a simple explanation, don't complicate by talking about everything else other than bank 1 and bank 2 located.

[slacker_DIY]

It took so long to see your red pen point to bank 2 or bank 1 at 2:15

[twincitiesdashcam]

Excellent explanation! Great for my 2012 Rav4 V6.

[bromporke]

VERY helpful. Your engine code will tell you if it’s exhaust vs intake side, for example: I have P0025, which is an “exhaust camshaft for bank 2” so I need to replace the VVT sensor on the very front side of the engine block as you’re looking down into the engine compartment.

[ahmadghosheh]

Thank you for pointing the A and B sensors.

[romantorrano]

Thank you so much I learn all I wanted to know appreciated

[MRSGrumbleCakes]

Thanks for this! I have the Bank 2 code and it's been difficult to find position info on this for the Sienna.

[javamochafrap]

can you do a video to replace BOTH the 2012 sienna vvt solenoids, left and right, or bank 1 and bank 2 ??

[dhood]

Great videos. It looks like to get to the solenoids or sensors on bank 1 you have to remove the intake manifold. Is there an easier way?

[jeremycantu]

Auto Repair Guys Thank you for this video. It totally saved us $$$$ when this sensor went out on a long trip. Keep up the great work!

[ahmedyamen]

Thank you for this wonderful and useful video
My question is, is the mark on the crankshaft in the crank cup on 0 or on 10? Please reply if you are so kind. My engine is 2gr-fe v6

[kayannabrown]

I changed the oxygen sensor bank 1 #2 and did not work so take it back out and it black again what given the problem now still getting p0037 code what to check for

[azablue]

Hi I have 2011 Sienna V6. It was throwing P0138 code every other day after I cleared it. It is said that its Bank 1 Sensor 2, should I replace the oxygen sensor located after the catalytic connverter and is it exactly located in the passenger side? Thanks in advance.

[modisenyanesebetlela]

hei..thank you for the video. i cant locate the camshaft position sensors on my Lexus RX300 1998, V6 ENGINE

[westernapache]

Find the bank with the coil/spark plug closest to the front of the engine. (Front being where the drive belts and pulleys are.) Bank 1 has cylinder one in it. Cylinder one is farthest forward.

[titoacruz]

Thanks for the explanation. Good info!

[trainingtechlabs]

Thanks for sharing your video it was very helpful to me. I have RX350 2010 same engine with Sienna and I have mild oil leak like moist very little oil coming from Variable Camshaft Timing Solenoid, I don't have any error in the dashboard. My question do I need to clean them or maybe change o ring?

[jayveecee]

Hi guys, I apologize for my question being unrelated, I just wanted to ask, I recently purchased a used 2011 Yoyota S ienna, my complaint is that, when I make a left turn (only on left turn) a door icon ( Not flashing) and a flashing yellow triangle display on my dash, when I straighten my Sienna out the icons are NOT displayed any longer, what might be the issue?

All doors are fully locked and the fuel cap is fully seated..I checked the fuses and they are ok...

[haskelpauyo]

Hello sir, had a miss fire on my 2008 Toyota sienna, cylinder 1-4-6 so I replace all the spark plugs, connectors and coil, done put everything back, double check everything looks good but the car will only crank but no start, before the obd2 port was working now the scanner turn on but no communication with the computer. Do you know what that may be? thank you.