Customer States Air Tool NO POWER!

Customer states the impact wrench he bought has NO POWER?! You need these high-flow air fittings! These performance air fittings will make your weak impact wrench or air tool very powerful! Mechanic air tool performance is about increasing air flow through the tool. TOOLS BELOW: ↓↓↓↓

Tools:

Milton V-Style air fittings are the BEST! Much better than M-Style pneumatic fittings. Remove air flow restrictions at your air compressor too.

#shorts #customerstates #automotive #mechanic #tools #tooltips #airtools #ingersollrand #toolreview #toolreviews #youtubeshorts

[MattsShop]

Hey Yall! Try them for yourself!
As an Amazon Associate I earn from qualifying purchases.

[modificationnation]

90% of the time if you have no power it’s because you need to oil the gun.

[benjaminberg]

If there old, run trans fluid through them, if there new make sure it's not on the low setting, and then run trans fluid through them anyway

[NDC]

A 2235timax is rated at 6cfm. Dosen't matter how big your fittings are if your compressor isn't up to the task.

[weekdys]

Backwards compatible makes it worth a try. Good selling point, like "higher air flow but you also don't have to replace every fitting you own just to decide you dont like it." Genius

[ViperSRTnACR]

Also if you're buying a used gun, it's a good idea to pop the cover off and check for any oxidation on the parts you'll want to clean off with 600-800 grit sandpaper. After checking the veins move freely in their slots, reassemble and run some trans fluid through it as others have said and keep it oiled regularly.

[TheCrystalGlow]

Remember though, when you increase flow, you decrease line pressure. Make sure you have appropriate new pressure settings from the pump when using.

[biskutman]

Love you before and after shots where you hade the tool turned down to the lowest setting. And then the after where it was at the highest setting. Great demonstration in deceptive marketing.

[rogerjustice]

Lol I just love reading the comments you would think this 200 dollar air impact was a Nasa rocket. It's a tool people, use it, if you break it fix it. Me personally if I can get more performance from a tool I already have why would I not do so. Sure beats going out and buying a more expensive tool for even more money than a high flow air fitting would cost. Thank you for the tip I'm planning on giving it a try.

[CarswithNash]

My air impact has a rather thick layer of dust on it because I haven’t used it for several years. Cordless impacts are so much nicer. Those couplers are very important to use on sprayguns, you won’t have a proper spray pattern otherwise because the gun will be starving for air.

[loganthesaint]

I use swivels, don’t have those fittings. I have c style. Haven’t had a problem yet. And my pressure from tank is correct going through 100’ of air line.
My flow is great.

[gutterpunk]

When the tool said "ugga dugga" I felt that

[vinnyaudi]

Been running these for years now. The purple ones. Massive difference

[butre.]

works with the regular fittings? does it leak with the regular fittings? none of my bigger quick connects fit the smaller ones, I have to keep an adapter for the smaller fittings

[Eds]

And both took about the same amount of time to remove the nut.
If the opening is bigger, the compressor has to kick on more often. Making it wareout faster. And most likely harder on the tools as well.

[WarWolfX]

I use Milton G-style, with a 1/2 hose. It's the best flow out there. I use it on my blast cabinet and impact gun.

[dukefuller]

I got rid of quick connect at compressor side of hose, no regulator. Compressor kicks off at 145- its all good

[PearComputingDevices]

I rebuild these at work because our opperators have no clue. You could probably do a quick video of oiling and vane maintenance... it's just as critical air flow itself. Doesn't matter how much air you ca deliver if you can't properly turn the vanes within!

[dresser]

I have said this for years 1/4 3/8 1/2 hose it doesn't matter when the quick disconnect fitting has a hole in less then 3/16 of an inch because it acts like an orifice and restricts air flow I remember many years ago some garages used to directly plumb the hose to the tool especially impact guns

[kartboarderg]

Yes this is fact I still have my air compressor and I still run v but I don't have an impact anymore but yeah it does really help with power also with short holes also with a bigger hose