Best AFFORDABLE 10'' Dual Bevel MITER SAW (You Will NEVER GUESS The BRAND!)

Best AFFORDABLE 10'' Dual Bevel MITER SAW You Will NEVER GUESS The BRAND, but the #VeryCoolGang will know after the #unboxing , #Setup and test run of this 15 amp 10 inch corded compact jobsite double bevel compound sliding miter saw that the (MS6305-00) may be the best affordable 10 inch dual bevel saw and you'd never guess the brand is Skil Tools

[larryjohnson]

Hi Vince. I just want to give ya big thank you for your review of this saw.
I purchased this saw a little over a year ago based on this review. I've since used this saw pretty heavily all this past summer doing 3 composite decks and a complete vinyl siding job on our new house. I changed the blade to a 60T Diabolo for this work. It cut the vinyl like butter. FWIW, one has to pull the blade thru the vinyl rather than the traditional push thru in order to get clean, non-chipped cuts. I got precise cuts on all the composite decking as well...all flawless. It's a great saw, especially at this price point.
Here recently, I pulled that blade back off and gave it a good cleaning prior to starting the next phase of our house project. I've recently been doing window trim work primarily following the method used at Finish Carpentry TV (Richard)....all using this saw. So far, so good!!! Love this thing!!
Again, thanks!!!

[cabman]

When I first got into woodworking, I bought a Skil table saw, band saw and bench sander. I still use these same ones 25 years later.

[lemonbar]

Not only is this a wonderful review, but you also showed how to adjust it and tune it up right out of the box. That's something no one else does! Thank you!

[iratevagabond]

Upgraded from an old craftsman hand-me-down 10", to a Delta Cruzer 12". Love it.

[fretlon]

I got this saw last year and used it to rebuild my deck, including cutting all the composite boards to length. It's been a champ and I couldn't be more pleased with it. I liked it so much I just bought the Skil 10 inch portable tablesaw.

[spencerhamilton]

Picked this saw up two weeks ago on Amazon for 250. Loving it so far!

[nxzkqit]

I just got it for 230$ including tax. I’m quickly falling in love with Skil. Their 14amp router combo is the best value out there, hands down. It’s gone as low as 100. I’m using this saw primarily to break down lumber and will soon need it for a lot of quick cuts when I move into a new place/shop. As far as I can tell with the few test cuts, it’s dead on straight from the factory. Good job skil

[slpstang]

I was on the fence ordering one today for my flooring job, you gave me the confidence to pull the trigger. Thanks for the review!

[avikimhi]

Being new to the construction world you’re videos really help me in many things thank you very much

[allanjustingonong]

Had it for couple of months now and IT IS A GREAT SAW. Just a regular homeowner here

[joshuagarner]

I’m a believer. Own the miter saw, table saw and a few 12v cordless tools. The saws have been absolutely amazing. I been actually shocked with the cordless tools! If you a weekend warrior and want good tools at a good price, in my opinion SKIL is hard to beat.

[fdwsr]

I just purchased the same saw, so far so good I am just a homeowner with small projects.

[kthoennes]

Thanks very much for this review. I had a cheapie Chicago Electric sliding miter saw for many years, but now I'm working on a home theater project with a ton of crown and other moldings, so I needed to step up. I didn't spend a million dollars on this saw, but it's a huge improvement. Accuracy is very impressive, just as you found. I did change the blade to a 60-tooth, low angle ATB (couldn't find a negative rake in any local stores) but you're right, the stock blade was impressive out of the box for a 40T. Thanks for confirming my good impression. Great saw for the money.

[larryjohnson]

Just received and set up this exact saw this afternoon. It was dead on right out of the box. There were a couple or minor things I ran into: 1. The saw lock was pretty loose and would engage on every cut locking the saw down. There is a 2.5mm set screw there on the side of the sliding lock bolt which I slightly tightened up and solved that issue. 2. I wanted to put a 60T fine-cut blade on it. Loosening the cover screw to move the cover back to expose the blade bolt was somewhat of a challenge....until I realized that the screw has to be almost completely backed out in order for the cover to move. BTW, blade bolt is reverse thread: clockwise to loosen.
I made several cuts with various thicknesses, and this beast ate it up.
Overall, it's a nice piece of equipment, especially for a DYIer/homeowner/hobbiest. Great saw.
I know this video is over a year and a half old, but still want to say "thank-you, Vince", for putting it out there for us.

[cardo]

Vince is not just a charismatic tool tester and bargain hunter he is also a skilled tradesman 👍🏽

[pastameatball]

Picked this up for $250 this week. Very happy to see you have it a positive review

[pointedspider]

U know something vince....I believe you sir have improved your game when it comes to reviews!

[BurnAfter]

I like 10" because I can share blades with my table saw. Seems trivial but keeps me from buying 3 different sizes (miter, table, & circular).

[paulx]

Impressed you showed how to adjust the saw. I think even though the price is right, everyone should know basic maintenance of their tools.

[pmvoice]

I've had my 10" Skil miter saw for a while now and I gotta say it is a real nice machine. I has all the major features and it does everything it's supposed to do. Stock blade is ok for a while but you'll need to replace it with a better one, but that's common.