Unboxing, setup & bleed of Daytona 3-ton floor jack

Unboxing and setup of a Daytona 3-ton floor jack (not sponsored).
Also bleed/adding hydraulic jack oil to jack during setup.
Test lifting and lowering with the jack.

[Rspruill]

Fantastic tutorial! Simple and to the point. Keep them coming.

[TJ-hdym]

Thanks brother just got the jack and my dumb ass didn't understand the directions but watching this I got it much appreciate. Many thanks

[BOOSTEDDUDE]

Great work man! Made it much easier than trying to figure out what the Manual said which wasn't helpful. I just tested this Jack on my 3, 200LB Jetta and it's a little more than I need but better safe than sorry. I also went with a warranty since the old 1.5 TON Pittsburg this is replacing didn't last that long.

[BobFudgee]

Thank you, the manual was kind of confusing because it said on the jack do not tamper with screws but the manual said the opposite lol!

[Robs_Got_A_Gun]

Let me help out the NEWBIES, if you buy a Daytona, Pittsburgh or Snap on Jack. Do NOT Rotate the handle more than 5 rotations Counter Clockwise (Left) if you do up to 10 Rotations the Jack will start Exploding Hydraulic Fluid out of the "Rotation Assembly" LEARN from my mistakes lol 😂 other than that the Jack is excellent Quality. I just wish they woulda put a Stopper in the Rotation Assembly to prevent people from unscrewing it completely out of the jack snd leaking all the fluid out instantly

[ww]

Nice review of the Daytona long reach jack from Harbor Freight and I like that you showed the bleeding the air process from the hydraulic reservoir before the first use its very important this is done to insure proper performance of the Jack and will reduce the chance of failure 👍

[KarelleDIY]

Dude label this vid unboxing and setup ( and or bleed) you will get more views! Thanx!!

[langamaphumulo]

Thank you! I watched this video to set up my Daytona 3 ton jack and now it's ready to go to work!

[vroomkeys]

Nice video this taught me how to bleed n top off 👌🏼
Just bought the same jack

[masonburroughs]

Good video! Short n to the point! I hate when ther 20min long. I just need to fill mine n bleed it (low pro green)

[dbzA]

I bought this jack last summer and it worked fine. Now it's spring and it won't jack at all. I noticed that the only one of the two pumps at the rear of the jack under the handle are engaging. The other is stopped by some plastic stopper.

[thewiseguy]

When your jacking up the pump while letting the air, if the oil is coming out of the hole, is that good ?

[kendonhubbard]

I have two of these and both have the same issue, the lift up just fine, but when they are up in the lifted position with a car on them, the handle is extremely difficult to turn counter clockwise to lower it. Is there a way to fix this?

[jordonsengchanh]

My Daytona drops really fast when I barely start lowering it

[carmelom]

IF this is a new jack, then why the need to add hydraulic jack oil. If that's the case, then I think jacks oil should be shipped with a new jack.

[motocross]

How in the hell do you get the shipping block out? My handle is down as far as it goes and I can't remove it.

[mclovin_it]

I bought the same jack a couple weeks ago. In the video when you lowered the jack it went down slowly but on my jack when I try to lower it softly sometimes it lowers faster then it should. Any idea what it might be?

[snooka]

I just got the same jack. The springs in mine are black and look thin and flimsy. When I release pressure I can hear the damn springs clinking.

They get cheaper on the build recently?

[jewbury]

Mine kept leaking the fluid when I pumped it during the bleeding process, was that supposed to happen?

[SBigred]

When I try bleed air out I’m getting oil overflow no air…