How to Remove: Headlight, Side Panels and Glovebox/Frunk on a Can-am Ryker

How to Remove: headlights, side panels and glovebox/frunk on a Can-am Ryker

for Can-Am Ryker parts and accessories!

#CanAmRyker #CanAm #Ryker #RykerRydes

[marcimartinez]

Thank you so much for this video!! I was attempting to swap.out my OEM headlights for LED by just going through the back and was so frustrated! I've learned so much from watching your channel!!

[rykerparkingonly]

You always make things so easy for your followers. What originally might have been to intimidating, you now make simple. Well done.

[heatheronwheels]

The other half and I installed my lights without removing the whole housing. It was a nightmare. He installed his this way and it was a world of difference! Thanks for sharing this.

[johnd]

Good review, good analytical skills. I like the way you divided the project into five small steps.

[GrumpySpyder-Ryder]

I change out the headlights on both Rykers the hard way. Right side was the worst. I can see it would have been easier to remove the housing. Thanks again the the great videos.

[coreywiley]

Just followed your instructions, thank you so much for the video. Much easier to follow than the Slingmod instructions, they need to request use of your video. Again, thank you. Also, I used a T-30 and it fit perfectly? Probably the assembler used a different torx? Thanks Beth, and Tina (videographer).

[frozgt]

Yet another great tutorial video. I’m learning so much from your videos. You rock 🤙🏻. Thanks!!

[wendy]

👍🏻. This looked a whole lot easier than when you did it previously.

[larryselman]

Can not find your video for removing gas stains ! Thanks for all your help👍👍👍👍

[LouieDeLeon]

Beth, my frunk cover has a bunch of scratches. I tried googleing how to remove just the cover and only saw your video. My question is, can you just remove the frunk cover. I saw at cheapcycle that I can order just the cover. Thank you in advance for answering my question.

[sharonpinkosh]

Hey Beth, I just purchased a '22 Ryker 600 ACE and installed the SlingMods reverse jockey shifter, which required removing the lower left side panel. Shifter went on great, but now I can't get the panel back on. Any tips/tricks would be so appreciated. Am getting zero help from the dealership.

[michaelgregory]

G'day Beth, greetings from down-under and kudos for the content you continue to supply - it's always informative. Regarding the Ryker "push-pins" do you happen to know the specifications for these and are all the push-pins on a Ryker the same size??

[servantsoldier]

Beth of all the parts & accessories; why haven’t can am or you considered adding hazard flashing lights? As a retired fl law officer I’m thinking about traffic safety and tons of traveling motorists. I’m curious why can am haven’t added these much needed lights to their US Rykers even in ‘22.
Even you haven’t added it to your Ryker

[bullsback]

What are you do with the plastic washer that was on the original headlight do you leave that off and just use the black one that comes with that headlight?

[jamesrebeccaschnur]

It made me want to cuss out the Slingmods guy that does the video on LED headlight installation. Tha parts in the damn video were not even the same !!!

[johnphillips]

Just want to add: a CAUTION, it’s so easy to break the plastic on the CanAm panels! Be VERY CAREFUL, if you are not sure as to how a panel removes. Go to you-tube, and do full research on how to remove a given panel. These things are made really CHEAP, I’m certainly sorry to say this cause I own one. Also when you break one of these tabs, good luck finding any type of glue that will bond to this type of plastic. And who wants to buy a new panel just because you broke one of the fasting tabs.😡

[cookey]

Hi Beth, I hope you are well, G'Day, from down under.