$50 DIY How to Cut Quartz, Granite or Marble Counter with a Circular Saw.

DIY How to Cut Quartz, Granite or Marble Countertops with a Circular Saw. It shows how to cut using both dry and wet techniques. No special tools are needed.

I ALWAYS search for the lowest prices for my projects. Here are the best prices for the tools I used in the video (or similar).

Home depot sells a similar blade for $14.97.

2. Circular Saw by Ryobi at Home Depot for $ 39.00


$69 DIY How to Polish a Quartz, Granite or Marble Countertop Bullnose or Square Edge profile.

$41 DIY How to Cut a Sink Hole in Granite, Marble or Engineered Quartz

$21 DIY How to drill faucet holes in granite quartz or marble the fast and easy.

$50 DIY How to Cut Quartz, Granite or Marble Counter with a Circular Saw.

Will a Diamond hole (core) saw cut through wood? This video shows the result!

$66 DIY How to Bullnose Quartz or Granite Countertop Freehand, With an Angle Grinder.

DIY How to Transport and Move Quartz Granite, Marble, Countertop with a Car

[scottwillis]

The best type of dust mask is a half-mask respirator with P100 filters. 3M, AoSafety, etc. make them. Cheap paper dust masks don't do much because they don't seal to your face.
Silicosis is when silica particles (rock dust) get into your lungs and cause scarring. Scars don't work very well as lung tissue.

[martinpattison]

I cut granite slabs when I did my kitchen. Used a hosepipe, but put a plastic bag around the motor of the circular saw and wore rubber gloves. Saw was plugged into a GFCI outlet.

[barryroberts]

Thanks for this tuitorial!! I bought the blade you suggested for $15. A lot easier than i thought! Turned put great!!

[christ]

The only question that didn’t get answered for me is, do you cut from the finished side or the rough side?

[thibodoux]

This and your polishing video were what I needed to know. Thank you!

[authorsauditions]

The best video I've seen so far. Thank you!

[thriftytani]

Hi! This is Thrifty Tani. If my video helped you, You would help me a great deal if you clicked on the subscribe button. Youtube rules have recently changed making subscribers essential to keeping my videos and channel alive. Thank you!

[thriftytani]

Here are the best prices for the tools I used in the video (or similar).

Home depot sells a similar blade for $14.97.

2. Circular Saw by Ryobi at Home Depot for $39.97.

Thanks for Watching,
Thrifty Tani

[PhilipThompsonCanada]

Very good - short video, that shows everything. I would only add that scratches can be avoided by using tape between the bottom of the saw, and the stone. Well done. I am subscribing right now. You just saved me around $1500 with this lesson :-)

[cmetube]

I agree.1⃣. No need to buy a wet saw. 2⃣. Waste of money.

[dattdude]

Thank you man I needed this ...your very reassuring words and great video edits gave me confidence to take on the same project

[Cincyreds]

Is there a minimum amount of material you can cut? I have a piece of granite that would need just 0.5 inches taken off both ends. Will the small cut cause more chipping in the granite?

[kristinpingree]

For a narrow piece, like a sidesplash or backsplash, do you think a miter saw could work, or would it not be slow enough?

[MrVahe]

Thanks great video the thing looks easy. One question: at 0:28 there is a small dent in the stone that you did prior to using the saw. I suppose this is to avoid chipping correct? But how did you do it? With a grinder, with tape on, without? Thx

[RealEstateTrek]

how do you make the edges of the counter top look nice ? How do you sand the edges ? Did you double up the edges and sand them to make the counter top look thicker ? Thanks.

[NAFO_Badger_Brigade]

Wow I've been donated about £600 worth of granite worktop that I'm going to use for bits of shelving

[andy_o]

Thank you for the video. I have to Cut a quarter inch off of a marble countertop on the edge. approximately 2 feet of a cut, do I have to take the countertop off or can I keep it on?

[clatxw]

If you have a ogee edge on granite vanity top, is it better to start cut into the edge on the front or start cutting on the wall side (back) and finish in the front. I bought a 60” prefabricated top with the sink already installed and I need to cut approx 1.5” off the side so it will fit between two walls. Of course using the techniques and tools used in video. Excellent video, I am sure that it has helped many people and saved them lots of money.

[mikemel]

Silicosis or Electrocution? How about both!

[anthonyblair]

I can do this thanks got 3 large pieces of quartz with counter edgesI am going to cut up kitchen is going to be great